MANUAL ELDES ESIM264 V3.2
MANUAL ELDES ESIM264 V3.2
2. TECHNICAL SPECIFICATIONS
2.1. Electrical and Mechanical Characteristics
Electrical and Mechanical Characteristics
Mains power
16-24V 50 Hz ~1.5A max / 18-24V
1,5A max
Current in standby without external sensors and keypad
Up to 80mA
Recommended backup battery voltage, capacity
12V; 1,3-7 Ah
Recommended backup battery type
Lead-Acid
Backup battery charge current
Up to 900mA
GSM modem frequency
850/900/1800/1900MHz
Cable type for GSM/GPRS antenna connection
Shielded
Number of zones on-board
6 (ATZ mode: 12)
Nominal zone resistance
5,6kΩ (ATZ Mode: 5,6kΩ and 3,3kΩ)
Number of PGM outputs on-board
4
On-board PGM output circuit
1 R
OUT
Open Collector Output.
Output is pulled to COM
when turned ON.
Maximum commuting on-board PGM output values
4 x Voltage – 30V; current – 500mA.
BELL: Siren output when activated
Connected to COM
BELL: Maximum cable length for siren connection
Up to 100m (328.08ft)
BELL: Cable type for siren connection
Unshielded
AUX: Auxiliary equipment power supply voltage
13,8V DC
BELL+AUX: Maximum accumulative current of auxiliary equipment and
siren
1 A
AUX: Maximum cable length for auxiliary equipment connection
Up to 100m (328.08ft)
AUX: Cable type for auxiliary equipment connection
Unshielded
BUZ: Maximum current of mini buzzer
150mA
BUZ: Power supply voltage of buzzer
5V DC
BUZ: Cable type for mini buzzer connection
Unshielded
Supported temperature sensor model
Maxim®/Dallas® DS18S20, DS18B20
Maximum supported number of temperature sensors
1
DATA: Maximum cable length for 1-Wire communication
Up to 30m (98.43ft)
DATA: Cable type for 1-Wire communication
Unshielded
Supported iButton key model
Maxim®/Dallas® DS1990A
Maximum supported number of iButton keys
5
Maximum supported number of keypads
4 x EKB2 / EKB3
Y/G: Maximum cable length for RS485 communication
Up to 100m (328.08ft)
Y/G: Cable type for RS485 communication
Unshielded
MIC: Maximum cable length for microphone connection
Up to 2m (6.56ft)
MIC: Cable type for microphone connection
Unshielded
Wireless band
ISM868 /ISM 915
Wireless communication range
Up to 30m (98.43ft) in premises;
up to 150m (492.13ft) in open areas
Maximum supported number of wireless devices
16
Event log size
500 events
Maximum supported number of zones
44
Maximum supported number of pgm outputs
44
Cable type for zone and pgm output connection
Unshielded
Communications
SMS, Voice calls, GPRS network, RS485, CSD
Supported protocols
Ademco Contact ID, EGR100, Kronos, Cortex SMS
Dimensions
140x100x18mm (5.51x3.94x0.71in)
Operating temperature range
-20...+55°C (-4... 131°F)
Humidity
0-90% RH @ 0... +40°C
(0-90% RH @ 32... 104°F) (non-condensing)
2.2. Main Unit, LED and Connector Functionality
Main Unit Functionality
GSM MODEM
GSM network 850/900/1800/1900MHz
modem
SIM CARD
SIM card slot / holder
DEF
Pins for restoring default settings
USB
Mini USB port
FUSE F1
3A fuse
ANTENNA
GSM/GPRS antenna SMA type connector
MODULES
Slots for EA1, EA2 or EPGM8 module
EWT1
Slots for EWT1 wireless module
C4
C3
SMA
ANTENNA
FU
SE
3A
PW
R
Z4
Z3
Z2
Z1
C1
C2
NE
TW
O
R
K
Z5 Z6
ST
A
TU
S
EWT1
MODULES
SIM CARD
DEF
PRG
USB
OPEN
C
O
M
BELL- BELL+
G
Y
C2
A
U
X-
A
U
X+
A
C
/D
C
A
C
/D
C
Z1 CO
M
Z2 Z3 CO
M
Z4
D
A
T
A
+5
V
M
IC
-
M
IC
+
BU
Z
-
C1
BU
Z
+
C
O
M
C
O
M
Z6
Z5
G S M
MO DE M
AKU+
AKU-
1
LED Functionality
NETWORK GSM network signal strength and status
C2, C1
PGM output C1 and C2 status. Steady ON = turned ON; OFF
= turned OFF
Z1
Zone Z1 state (ATZ mode: Z1 and Z7). Steady ON = violat-
ed; OFF = restored.
Z2
Zone Z2 state (ATZ mode: Z2 and Z8). Steady ON = violat-
ed; OFF = restored.
Z3
Zone Z3 state (ATZ mode: Z3 and Z9). Steady ON = violat-
ed; OFF = restored.
Z4
Zone Z4 state ( ATZ mode: Z4 and Z10). Steady ON = vio-
lated; OFF = restored.
Z5
Zone Z5 state (ATZ mode: Z5 and Z11). Steady ON = violat-
ed; OFF = restored.
Z6
Zone Z6 state (ATZ mode: Z6 and Z12). Steady ON = vio-
lated; OFF = restored.
PWR
Power supply status. Steady ON = power supply OK; OFF
= no power.
STATUS
Micro-controller status. Flashing = micro-controller OK;
OFF = micro-controller fault.
NETWORK indication
Description
OFF
No GSM signal - SIM card
missing; PIN code enabled
on SIM card; GSM antenna
disconnected or faulty; GSM
operator’s fault; GSM signal
unavailable in the are
Flashing every 3 sec.
Poor GSM signal strength
Flashing every 1 sec.
Medium GSM signal
strength
Flashing several times per sec. Good GSM signal strength
Steady ON
Excellent GSM signal
strength
Connector Functionality
Z1 - Z6
Security zones
COM
Common terminal for all zones
DATA
1-Wire® interface for iButton® key and temperature sensor connection
+5V
Temperature sensor power supply contact (+5V)
MIC-
Microphone negative terminal
MIC+
Microphone positive terminal
BUZ-
Mini buzzer negative terminal
BUZ+
Mini buzzer positive terminal
C1 - C4
PGM outputs
Y
RS485 interface CLOCK terminal (yellow wire)
G
RS485 interface DATA terminal (green wire)
COM
Common return terminal
BELL-
Siren negative terminal
BELL+
Siren positive terminal
AUX-
Negative power supply terminal for auxiliary equipment
AUX+
Positive power supply terminal for auxiliary equipment
AC/DC
Mains power terminal
AKU-
Backup battery negative terminal
AKU+
Backup battery positive terminal
