Eldes ESIM264, Installation Manual

Page: 20 / 60

38 39 38 39 EN EN MANUAL ELDES ESIM264 V3.2 MANUAL ELDES ESIM264 V3.2
Disarm
the
system
36
Disarm
the
system
37
The system will arm/disarm the partition corresponding to the one that EWK1/EWK2 wireless keyfob is assigned to (see 23.6.
EWK1/ EWK2 Wireless Keyfob Partition ). For example, if EWK1/EWK2 wireless keyfob is assigned to Partition 1, the user
will be able to arm/ disarm only Partition 1. To arm a different partition than the EWK1/EWK2 wireless keyfob is assigned to, pair
another EWK1/EWK2 keyfob with the system and assign it to a different partition.
For more details on how to manage EWK1/EWK2 keyfob buttons, please refer to ELDES Configuration Tool software‘s HELP
section.
12.7. Arm-Disarm by Zone
ARM/
DISARM
ZONE
The Arm-Disarm by Zone feature allows to use a zone for arming and disarming the alarm system when the zone is violated and
restored. The process is performed by providing a low-level pulse for more than 3 seconds into the specified zone. It means that
violating and restoring the zone leads to system arming and by repeating this action the system becomes disarmed. The system
will arm/disarm the partition (-s) that the zone is assigned to. This method can be set up for one on-board zone only.
Set zone for Arm-
Disarm by Zone
method
EKB2
Menu path:
OK
→
CONFIGURATION
→
OK
→
aaaa
→
OK
→
ZONES
→
OK
→
ARM/DISARM BY ZONE
→ OK → ZONE 1... 12 → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 34 and on-board zone number:
34 nn #
Value: nn – on-board zone number, range – [01... 12].
Example: 3403#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Disable Arm-Disarm by
Zone method
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ARM/DISARM BY ZONE
→ OK → N/A → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 34 and parameter status value
34 00 #
Example: 3400#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
12.8. Disabling and Enabling Arm/Disarm Notifications
By default, when the system is successfully armed or disarmed, it replies with confirmation by SMS text message to:
• user phone number, sharing the same partition as EKB2/EKB3 keypad and user code, iButton key, EWK1/EWK2 wireless keyfob or zone,
set up for Arm/Disarm by Zone method.
• user phone number that the system arming/disarming by free of charge phone call was initiated from.
• user phone number that the system arming/disarming by SMS text message was initiated from.
The confirmation SMS text message is sent to the user phone number regarding each partition separately and contains system status and
partition name.
To disable/enable this notification for individual user phone number, please refer to the following configuration methods.
Disable arm/disarm
notification for
individual user phone
number
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → USERS → OK → USER 1... 5 → OK → SEND ARM/DARM SMS → OK →
DISABLE
→
OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 75, user phone number slot and parameter status value:
75 up 0 #
Value: up – user phone number slot, range – [01... 05].
Example: 75030#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Enable arm/disarm
notification for
individual user phone
number
EKB2
Menu path:
OK
→
CONFIGURATION
→
OK
→
aaaa
→
OK
→
PRIMARY SETTINGS
→
OK
→
CALL/SMS
SETTINGS → OK → USERS → OK → USER 1... 5 → OK → SEND ARM/DARM SMS → OK →
ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 75, user phone number slot and parameter status value:
75 up 1 #
Value: u p– user phone number slot, range – [01... 05].
Example: 75041#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, the system sends SMS text message only to the first available user phone number when the system is successfully armed/
disarmed. If the system did not receive the SMS delivery report during 45 seconds, it will attempt to send the SMS text message to the next
listed user phone number. To ignore the SMS delivery report and allow/disallow the system to send the SMS text message to every listed
user phone number, please refer to the following configuration methods.
Enable arm/disarm
notification for all
listed user phone
numbers
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → CALL/SMS
SETTINGS → OK → SEND ARM/DARM ALL → OK → ENABLE → OK
Value: aaaa – 4-digit administrator password.
EKB3
Enter parameter 22 and parameter status value:
22 1 #
Example: 221#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.