manualshive.com logo in svg

ekwb EK-Quantum Vector FE RTX 3080, User Manual

Share
Download
ekwb EK-Quantum Vector FE RTX 3080 User Manual Download Page 19

- 19 -

To make sure the installation of EK components was successful, 
we recommend you perform a 24-hour leak test.

When your loop is complete and filled with coolant, connect the 
pump to a PSU outside of your system. Do not connect power to 
any of the other components. Turn on the PSU and let the pump 
run continuously. 

Inspect all parts of the loop, and in case the coolant leaks, fix 
the issue and repeat the testing process. To prevent possible 
damage, please ensure that all hardware is dry before the system 
is powered on.

TESTING THE LOOP

CONNECTING THE D-RGB LED STRIP 

STEP 1

Plug the 

4-pin D-RGB

 connector from the GPU water block to the 

D-RGB Header

 on your motherboard or controller. The LED strip will 

work only if the pin layout on the header is as follows: 

+5V, Data, 

Empty, Ground

.

Incorrect installation or installation to a wrong header can 
damage to the LED strip or the header itself!

STEP 1

D-RGB HEADER

RGB HEADER

Summary of Contents for EK-Quantum Vector FE RTX 3080





















Reviews:

No comments

Brands by name

Popular brands

Load more brands