manualshive.com logo in svg

ekwb EK-Quantum Vector FE RTX 3080, User Manual

Share
Download
ekwb EK-Quantum Vector FE RTX 3080 User Manual Download Page 11

- 11 -

STEP 4

PLACING THE BLOCK ON THE GRAPHICS CARD

This procedure is the same for all full-cover water blocks.

Carefully position the water block with preinstalled standoffs on 
the graphics card. During this process, make sure you have aligned 
mounting holes of the PCB with holes of the water block (the same 
applies to other tops). 

Pay attention not to use too much force when pressing the 
block down to the PCB since chip dies are prone to cracking.

STEP 4

For this Step, you will need:

M 2.5 PVC Washer

(4 pcs)

M2.5 x 4 AX1 

Screw (4 pcs)

Phillips Head 

Screwdriver

4 mm

STEP 5

M2.5 x 4 AX1 SCREW

M2.5 PVC 
WASHER

STEP 5

ATTACHING THE BLOCK TO THE GRAPHICS CARD

Use four (4) M2.5 X 4 AX1 screws and M2.5 PVC washers, as 

shown in the image. Tighten the screws around the GPU core 

evenly using the Phillips head screwdriver. Always use a plastic 

washer under each screw! 

Summary of Contents for EK-Quantum Vector FE RTX 3080





















Reviews:

No comments

Brands by name

Popular brands

Load more brands