background image

 

- 17 - 

- 17 -
 

and  then  tighten  screws.  If  you  need  to  change  parts,  please  contact  your  nearest  after  sale  service 
dealer. 

8. Fault analysis

 

If the truck after to following the instructions of the chapter (6) is still at cause of functioning. 
Table Failure analysis of 6: 

Fault 

Reason 

 

Repair 

 

The goods cannot ascend 

 

Excessive weight 

 

Decrease the maximum load 
capacity is shown on the nameplate 

 

Battery discharge 

 

Charge the Battery   

 

Enhance the fuse failure 

 

Check and the eventual 
replacement of ascending fuse 

 

The hydraulic oil level too low 

 

Check and finally filled with 
hydraulic oil 

 

The oil spills 

 

Seal repair tubing and / or cylinder 

 

 

Hydraulic Fluid 

 

Oil is too high 

 

Reduce oil 

 

The goods cannot be 

dropped 

 

Oil dirty blocking control valve 

 

Check the hydraulic oil and valve. 
Replace the hydraulic oil if 
necessary 

 

Declining electromagnetic valve 
does not open or damage 

 

Check or replace down solenoid 
valve 

 

Truck cannot operate 

 

Check battery charge 

 

Completely charge 

Battery is not connected 

 

Check connections 

 

Fuse failure 

 

Replace fuse 

 

Low battery 

 

Charge Battery 

 

The emergency stop switch is 
activated 

 

Pull the knob to eliminate the 
emergency stop switch Functioning 

 
The handle at the operation area 

 

 
The handle is moved to the braking 
zone 

 

Truck travels only in one 

direction 

 

Accelerator and connectors do not 
function 

 

Check the accelerator and 
connector to ensure proper contact 

 

Stacker walking very 

slowly 

 

Low battery 

 

Check the discharge display battery 

 

Has launched the electromagnetic 
brake 

 

Check the electromagnetic brake 

 

The handle is not connected or 
damage related wiring harness 

 

Check the wiring harness and 
connector handle 

 

Truck suddenly starts 

 

The AC controller damages 

 

Replace the controller 

 

The accelerator is not transferred 
back to the middle position 

 

Repair or replace the accelerator 

 

 

Summary of Contents for EB12EA Series


















Reviews: