manualshive.com logo in svg

Ekinex EK-CG2-TP, Applications Manual, Page: 28 / 91

Share
Download
Ekinex EK-CG2-TP Applications Manual Download Page 28

Applicatio Manual 

                                Universal Interface 4 DIN/NTC EK- CG2-TP 

 

 

Revisione 1.0.0 - Aggiornato: 04/09/2017

 

© SBS S.p.A. 

– Tutti i diritti riservati 

MAEKCG2TP_EN 

Pag. 28 

 

 
 

9.0.1   Info su EK-EG2-TP 

 
The folder 

About EK-CG2-TP

  is for information purposes only and does not contain parameters to be set. The 

information given is: 
 
© Copyright SBS S.p.A. 2017 
Application software per ETS4/5 
Version 1.00  
Universal Interface 4 DIN / NTC 
 
SBS S.p.A. 
Via Circonvallazione s/n 
I-28010 Miasino (NO) Italy

 www.ekinex.com [email protected]

 

 
 

9.0.2 General setting 

 
The parameters in this section define the overall behaviour of the device, including the setting that defines which 
and how many channels are available 
 
 
 

Parameter name 

Conditions 

Values 

Delay after bus voltage recovery 

- 

hh:mm:ss.fff  
(

00:00:04.000

) 

 

Delay before bus telegrams can be sent after a recovery of the bus voltage. The delay time affects 
the  transmission  generated  by  an  event  as  well  as  the  cyclical  transmission.  For  the  cyclical 
transmission:  after the  delay time  finished,  the cycle  restarts  and the  first  telegram will  be sent 
after the cycle time. 

Logic functions 

 

enabled / 

disabled

 

 

Enables the folders to configure AND, OR e XOR logic functions and their relative input and output 
communication objects. 

 

9.0.3  Input configuration 

Nome parametro 

Condizioni 

Valori 

Input  

x 

-

 

disabled 

independent or single 

coupled 

temperature probe 

 

Sets the operation mode for inputs associated with Input x. The identification of which inputs and 
physical inputs corresponding to a given number (eg 1A - 2B - 4A etc.), depending on the layout 
chosen for the plates, depends on the parameter "General / Input Configuration 

Function A 

Input 

x

 = independent or single 

 

enabled /

 disabled 

 

 

Enables or disables the capability to generate events for the first pushbutton of the input. 

Type 

Input x = independent or single 

Function A = enabled 

send values or sequences 

dimming 

shutter or venetian blind 

scene

 

 

Determines the kind of function performed by the FIRST Input input. 
Further parameters for the selected function will appear in the individual Input configuration sections 
(see below). 

Temperature probe  A 

Input x = temperature probe 

Function A = enabled 

enabled

 /

 

disabled

 

 

 

Determines the kind of function performed by the FIRST Input input. 

Further parameters for the selected function will appear in the individual Input configuration sections 
(see below). 

Function B 

Input x = independent or single 

 

disabled 

enable 

in parallel with function A, as a function. single 

copy parameters from function A 

Summary of Contents for EK-CG2-TP




























































































Reviews:

No comments