eka MILLENIAL MKF 1011 CTS Installation And Maintenance Manual Download Page 15

Page: 15 / 20

5 Troubleshooting

Type of fault

Cause of the fault

Corrective action

Control panel totally off
(the oven does not work)

Non-compliant connection to the
power mains

Check the connection to the mains

No mains voltage

Restore the power supply voltage

Blown electronic board protection
fuse (with microprocessor)

Contact a skilled technician

Cooking cycle on: the oven
does not start up

Door open or ajar

Close the door properly

Damaged magnetic sensor

Contact a skilled technician

Steam cycle on: no steam is
being generated in the
cooking chamber

Non-compliant water mains
connection

Check the connection to the water
mains

Closed stopcock

Check the cock

Obstructed water inlet filter

Clean the filter

Damaged water inlet solenoid valve

Contact a skilled technician

Steam generator safety thermostat
on

Contact a skilled technician

Closed door: steam escapes
through the gasket

Non-compliant gasket assembly

Check gasket assembly

Damaged gasket

Contact a skilled technician

Loosened handle "nose"

Contact a skilled technician

The oven does not cook
evenly

One of the motors is down or
operates at low speed

Contact a skilled technician

The motors do not reverse direction

Contact a skilled technician

6 Possible alarms

Identify the causes that stop the oven from working

Type of alarm

Cause of the alarm

Effect

Corrective action

Temperature probe

not detected

Cooking cannot be

started up

Cooking chamber probe-
electronic board/
microprocessor
connection down

Cooking cycle cannot
be started

Contact a skilled
technician

Damaged cooking chamber
probe

Core probe not

detected

Cooking cannot be

started up

“Core” probe-electronic
board/microprocessor
connection
down.

Impossible  to  start  a
cooking  cycle  which
requires  setting  the
"core”

temperature

parameter

Contact a skilled
technician

Damaged (needle-
shaped) “core” probe

Overheated motors

safety circuit breaker

tripped”

Overheated motor (tripped
motor thermal protection)

Oven operation
disabled

Contact a skilled
technician

Summary of Contents for MILLENIAL MKF 1011 CTS





















Search results

Summary of Contents for MILLENIAL MKF 1011 CTS

Reviews:

Related manuals for MILLENIAL MKF 1011 CTS

Brands by name

Popular brands

eka MILLENIAL MKF 1011 CTS, Installation And Maintenance Manual

Search results

Summary of Contents for MILLENIAL MKF 1011 CTS

Reviews:

Related manuals for MILLENIAL MKF 1011 CTS

Brands by name

Popular brands