background image

ITS Partner O.B.S S.L · Av. Cerdanyola 79-81 Local C 

08172 Sant Cugat del Vallés · Barcelona (Spain)  

Phone: +34935839543  ·  [email protected]  ·   www.ek.plus

 

12

 

 

 

CM 8SH CI-TC 

USER MANUAL

 

 

Information window on each MUX output throughput: 

Four bars are displayed corresponding to each MUX output. The green line indicates the percentage of 
channel occupied. 

The number above indicates the total throughput being transmitted. 

At  the  end  of  each  bar  there  are  two  numbers:  the  first  number  indicates  the  throughput  being 
modulated  on  that  channel  and  the  second  the  maximum  possible  throughput  for  the  selected 
modulation parameters. The first number should not exceed 80% of the second unless for services with 
constant throughput. 

DVB-C output card: 

For DVB-C it is all identical to the DVB-T except for the modulation parameters: 

 

Const.: Select the desired output constellation: 256QAM, 128QAM, 64QAM, 16QAM. 

 

Band: Output channel bandwidth: 7MHz or 8MHz. 

 

S.R.: Enter the required value. 

Whenever the modulation of a head-end module is changed, the power supply must be reset. 

 

Advanced Configuration: 

LCN Function: 

The transmodulator enables labeling the information Transport Streams so that the TV programs are 
displayed in order on the TV set, in its program guide as specified from the head-end. In this way, all TV 
sets with the LCN function will have the same contents in each program number on the TV set. Although 
this function is useful for hotels or cable operators, as it avoids manual reordering of the programs on 
each TV set,  tuning  of  each  TV set is required. To  perform the program number assignment,  simply 
double-click on the LCN column of the program to be changed and apply the number of the desired 
position. Example: 

 

Configuration of SID and NSID parameters: 

The transmodulators 

enable a “remapping” of the SID fields. This functionality will enable to change the 

content of a program in the TV, leaving it in the same output channel of the head-end module, without 
the need to retune the TV. To do this, it is necessary to activate the new program to be transmitted in 
the same NSID where the previous program being broadcasted, by double clicking on the NSID column 
of the program to be changed. Example: 

 

 

Summary of Contents for 082256

















Reviews: