eisfink varithek acs 1000 ec User Manual Download Page 52 | Manualshive

Page: 52 / 56

eisfink varithek acs 1000 ec User Manual Download Page 52

Troubleshooting

52

Eisfink Max Maier GmbH & Co. KG

8.12

Disinfect the appliance as required



Please clarify this with your hygiene officer.

8.13

Keep ready for next use in dry condition



Dry the inside of the appliance and leave the door open until the residual moisture has dried off.



Store appliance at room temperature.

8.14

Ensure preservation of the product identification

The product identification of your appliance on the type plate provides important technical data for use
and a unique identification, which is necessary for replacement and wearing parts, for example. Safety
instructions assist safe handling.



Make sure that the appliance is correctly identified. Inspect this at least 1x every six months.

Chapter ‘Product identification’, page 14

9

Troubleshooting

9.1

Notes on troubleshooting

WARNING

Danger of electric shock. Dangerous electrical voltage.

►

Disconnect the connecting plug on the unit before starting repair work.

►

Have all electrical repairs carried out by an authorised electrician only.

►

Any interference in the ‘plasma generator’ is forbidden.



Possibility of malfunction after power interruption.

Disconnect the unit from the mains

completely after a power failure. Then switch back on.

Any repairs during warranty period may only be carried out by the manufacturer's service department
of Rieber. Please contact the manufacturer's service department of Rieber.

«
...
50
51
52
53
54
...
»

Summary of Contents for varithek acs 1000 ec

























































Reviews:

No comments