eisfink varithek acs 1000 ec User Manual Download Page 30 | Manualshive

Page: 30 / 56

eisfink varithek acs 1000 ec User Manual Download Page 30

Use

30

Eisfink Max Maier GmbH & Co. KG

7.5.2

Switching on / Switching off



Switch the ON/OFF pushbutton with indicator light on the air-cleaning-system

acs

®

to ON.

▌

Control is in STANDBY.



Press

ON/OFF

button (1).

▌

During normal operation the OK LED shows a green light.

▌

The extraction system starts at the lowest fan speed, level 1.

Allow the ventilation to run on briefly if necessary, so that the vapours rising due to
residual heat cannot spread to the surrounding environment.



Press the

ON/OFF

button to switch off.

▌

The display goes out. The display is black.

7.5.3

Adjust ventilation intensity

Adjust intensity, levels 1 to 4



Press the PLUS button (5), to increase the level.
Press the MINUS button (4), to decrease the level.

▌

The selected level and the fan icon appear in the display.

TURBO is the highest ventilation intensity level.

Adjust TURBO



Press the TURBO button (3).

▌

The fan icon and TURBO appear in the display.

▌

After 5 minutes the fan switches back to the last selected ventilation
intensity.

«
...
28
29
30
31
32
...
»

Summary of Contents for varithek acs 1000 ec

























































Reviews:

No comments