GB
- 31 -
On a regular basis, check that the chain lubrica-
tion is working correctly. Test chain lubrication
before the
fi
rst cut, after several cuts and always
after any maintenance.
Chain lubrication
Always make sure the automatic oiler system
is working properly. Keep the oil tank
fi
lled with
Chain, Bar and Sprocket Oil.
Adequate lubrication of the bar and chain during
cutting operations is essential to minimize friction
with the guide bar.
Never starve the bar and chain of lubricating oil.
Running the saw dry or with too little oil will de-
crease cutting e
ffi
ciency, shorten saw chain life,
cause rapid dulling of chain, and lead to exces-
sive wear of bar from overheating. Too little oil is
evidenced by smoke or bar discoloration.
7.2.6 Chain maintenance
Chain sharpening
Note:
A sharp chain produces well-de
fi
ned chips.
When your chain starts to produce sawdust, it is
time to sharpen.
Chain sharpening requires special tools to ensure
that cutters are sharpened at the correct angle
and depth. For the inexperienced chain saw user,
we recommend that the saw chain be professio-
nally sharpened by the nearest professional Ser-
vice Center. If you feel comfortable sharpening
your own saw chain, special tools are available
from the professional Service Center.
Chain sharpening (Fig. 18)
Sharpen the chain using protective gloves and a
round
fi
le of.
Always sharpen the cutters only with outward
strokes (Fig. 19) observing the values given in
Fig. 18.
After sharpening, the cutting links must all have
the same width and length.
After the blades have been sharpened 3-4 times,
check the height of the depth limiter and if neces-
sary lower it with a
fl
at
fi
le and then round o
ff
the
front corner (Fig. 20).
Round o
ff
the front edges with a
fi
le.
7.3 Storage and transportation
Install the chain guard (4) before transporting or
storing the chainsaw.
Note:
Never put a chain saw into storage for
longer than 30 days without carrying out the fol-
lowing steps.
Storing a chain saw
Storing a chain saw for longer than 30 days re-
quires storage maintenance. Unless the storage
instructions are followed, fuel remaining in the
carburetor will evaporate, leaving gum-like depo-
sits. This could lead to di
ffi
cult starting and result
in costly repairs.
1. Remove the fuel tank cap slowly to release
any pressure in tank. Carefully drain the fuel
tank.
2. Start the engine and let it run until the unit
stops to remove fuel from carburetor.
3. Allow the engine to cool (approx. 5 minutes).
4. Thoroughly clean the saw.
Note:
Store the unit in a dry place and away from
possible sources of ignition such as a furnace,
gas hot water heater, gas dryer, etc.
After the saw has been in storage, perform the
steps listed in Paragraph 5 before starting the
chainsaw.
Transportation
•
Engage the chain brake.
•
Make sure the chainsaw cannot shift position
in order to prevent fuel loss, damage or injury.
7.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
Anl_GC_PC_1335_I_TC_SPK7.indb 31
18.07.2016 11:24:49
www.sidirika-nikolaidi.gr
Summary of Contents for 45.018.35
Page 6: ...6 19 20 18 21 A Anl_GC_PC_1335_I_TC_SPK7 indb 6 18 07 2016 11 24 43 www sidirika nikolaidi gr...
Page 218: ...218 Anl_GC_PC_1335_I_TC_SPK7 indb 218 18 07 2016 11 25 10 www sidirika nikolaidi gr...
Page 219: ...219 Anl_GC_PC_1335_I_TC_SPK7 indb 219 18 07 2016 11 25 11 www sidirika nikolaidi gr...
Page 220: ...EH 07 2016 01 Anl_GC_PC_1335_I_TC_SPK7 indb 220 18 07 2016 11 25 11 www sidirika nikolaidi gr...
