GB
- 42 -
code. Please contact the customer services
team to obtain your PIN.
6.5 Settings of the robot lawn mower
The main menu on the LCD (50) shows you the
current date and time settings of the robot lawn
mower, as well as the current charge level. At the
same time the status of the rain sensor and of the
wire signal and of the selected mowing program
will appear in the toolbar. On the control panel
you can use either the “SET” button (51) to make
settings on the robot lawn mower or the “MODE”
button (52) to start the robot lawn mower with
various mowing programs. Use the navigation
buttons (55) to go to the option where you want to
make the settings. Press the “BACK” button (54)
in order to exit the respective menu.
Making settings with the “SET” button (51)
The “SET” button (51) can be used to make the
basic settings on your robot lawn mower. Use
the navigation buttons (55) to move to where you
want to go and then use the “OK” button (56) to
con
fi
rm or the “Back” button (54) to discard the
settings you have made.
•
Schedule
Use the navigation buttons (55) to move to
the day of the week for which you want to
make the settings. In normal operating mode,
the robot lawn mower will automatically begin
to mow your lawn at the set time on the res-
pective day. It is recommended to base the
mowing time setting on 8 hours per day for
500 m² as a guideline. The selected working
time may need to be adapted to take account
of the garden’s size and complexity.
•
Zone
Where gardens have lots of angles, the robot
lawn mower may have problems reaching
every part of the lawn and mowing it comple-
tely. In this case you can select several star-
ting points on the perimeter wire (18). This will
enable the robot lawn mower to get to even
those parts of your garden that are difficult to
reach. The robot lawn mower will run the se-
lected distance along the perimeter wire (18)
and then start mowing in this part of the gar-
den (Fig. 6m). Use the navigation buttons (55)
to go to the point that you wish to change and
enter the distance and frequency accordingly.
The charging station (19) is automatically
defined as starting point 1. The two other st-
arting points can be selected as you wish. For
this you must measure the distance between
the charging station (19) and the starting
point in clockwise direction along the perime-
ter wire (18). With the frequency setting you
decide how often the robot lawn mower starts
its work from the charging station (19) or from
the respective starting points.
•
Boundary cut
For a tidy lawn edge you can activate the
„Edge mowing” setting. You can also set the
lawn mowing frequency, i.e. the rhythm in
which you want the edge of the lawn to be
mowed at the beginning of the work window.
In the standard setting the robot lawn mower
will begin work on all 7 work days by first mo-
wing along the entire perimeter wire.
•
Error log
From here you will be informed about the
latest error messages concerning your robot
lawn mower.
•
Rain sensor
The rain sensor (5) can be programmed using
this setting. The default factory setting for the
sensor is “On”. You can activate or deactivate
the rain sensor (5) and set its delay time. The
delay time defines how long the robot lawn
mower continues to remain in the charging
station (19) after the rain sensor (5) has dried.
•
Leaving the station
You can set how far and where the robot lawn
mower travels when it reverses out of the
charging station (19). First the robot lawn mo-
wer reverses the set distance before it turns
into the area to be mowed or towards its star-
ting point. Make sure that the set reversing di-
stance does not cause the robot lawn mower
to leave the area to be mowed.
•
General
- PIN code:
You can replace the default
PIN for the robot lawn mower with your own
choice of PIN. To do so, proceed as described
in the chapter “Locking mechanism / PIN”. Im-
portant! Make a note of the new PIN.
- Date & time:
Use the navigation buttons
(55) to go to the point that you want to change
and make the settings accordingly.
- Language:
Use the navigation buttons (55)
to activate the language that you want.
- Software version:
The current version of
the robot lawn mower software is noted here.
Mowing programs – “MODE” button (52)
Use the navigation buttons (55) to go to the
mowing program that you want to start. You can
always choose between “Main area” and “Se-
condary area”. More details of the two areas can
be found in the section “Before using for the
fi
rst
Anl_FREELEXO_LCD_BT_plus_SPK13.indb 42
Anl_FREELEXO_LCD_BT_plus_SPK13.indb 42
05.10.2022 11:10:36
05.10.2022 11:10:36
