background image

End of Life Indication:

: Amber light flashes every 45 seconds after 11 years to show the unit must

be replaced.

Dimensions

: 126 x 150 x 42 mm.

Weight

: 280g.

10. GETTING THE CO ALARM SERVICED

If your CO Alarm fails to work after you have carefully read all the instructions, checked the unit has been
installed correctly, and ensured that it has a good battery connected, return it for repair or replacement.
This should be where it was purchased, or alternatively return it in a padded box to “Customer Assistance
and Information” at the nearest address given on the CO Alarm or in this leaflet. (If the unit is beeping
then remove the battery as shown in figures 5&6). State the nature of the fault, where the CO Alarm was
purchased, and the date of purchase.

11. GUARANTEE

Ei Electronics guarantees the Ei206D Carbon Monoxide (excluding the battery) for two years from date
of purchase against any defects that are due to faulty materials or workmanship.

This guarantee only applies to normal conditions of use and service, and does not include damage
resulting from accident, neglect, misuse, unauthorised dismantling, or contamination howsoever caused.
This guarantee excludes incidental and consequential damage. If the Carbon Monoxide Alarm should
become defective within the guarantee period, it must be returned to where it was purchased or
alternatively to Ei Electronics, carefully packaged, with the problem clearly stated (see section 11
“Getting the CO  Alarm Serviced”) along with proof of the date of purchase. We shall at our discretion
repair or replace the faulty unit.

24

B16204-R0-206D-UC-ENG  20/6/08  3:49 PM  Page 26

Summary of Contents for Carbon Monoxide Alarm Ei206D





























Reviews: