G7-3865U Brief Instructions
Setting up the system - Hardware
.A
Notice: For safety reasons, make sure that the computer has been
disconnected from the power supply before opening it.
1. Open the computer
Please remove the four fl『st Screw In the
corners of the base plate (see Image 1)
and lift carefully remove It from the
computer.
0
—
—
（
甸
,
J
。
0
一
一
「
。
到
Image 1
2. Installation of the main memory (RAM)
Align the notch on the memory module with the tab In
the memory socket.
■■■■
carefully push
中
ememory module In 45-<legree angle
lnlo the slot
(1).
Now p
『
ess
小
e module down
(2)
unUI ii
clicks Into place
(3).
Foll
叩
this process for each RAM
module to be Installed.
l
兰
石
�
�
"""'"�
""""'""
3. Installation of mPCle modules
The computer contains one slot for mSATA
module(see M2) and one for another mPCle
module(see MS) .
Align the notch on the respective memory module with the tab In
the corresponding memory
吵
et. Press one for another mPCle
module(see M2). Then carefully Insert the module Into the slot at
a 45-degree angle. Now press the module down and fasten It with
asmall sa
如
In the cylinder provided for this purpose.
4. Installation of a ha『d disk
The computer has a space on its base plate for a
2.5 "SATA hard dlsk(see U3). Here a hard disk
(HOD/ SSD) is fastened from the inside with
four screws(see Image 4) and with the power
and data cable(see M3 and M4).
I -—
0 0
0 0
Image 4
5.
Completion of the hardware assembly
Put the base plate back on the computer. Place
them so that the ha
『
d drive is on the inside and
the four rubber feet are on the outside. Then
tighten the four screws In the corners again.
A
Notice: When starting, please press the "Del" key and load
the BIOS and load the "optimized" settings.
A
Notice: The Driver of this computer is backed up in the
"E
A
���i:e·: Careless battery
『
eplacementcan damage this
computer. Replace only with one of the same type. Dispose
of used batteries according to the manufacturer's
instructions.
U 1: Screw openings for hard disk(HDD / SSD 2.5 "SAT A)
M1: Socket for RAM modules
M2: Socket for mSATA SSD
M3: Power cable for hard disk(HDD / SSD 2.5 "SATA)
M4: Data cable for hard disk(HDD
/ SSD 2.5 "SATA)
MS: Socket for mPCle
(e.g. WLAN)
M6: SIM Card Slot
M?: CR2032 button
battery
MB: Guaranty Segel
G7-3865U Brief Instructions
一心
lo
A. Front
B. Rear
C. Underside
F1: USB 3.0 ports(4 pieces)
F2: D89 RS232 COM(1 piece)
F3: RJ45 RS232 COM(1 piece)
F4: HDMI display ports(1
piece)
F5: Reset button(1 piece)
F6: Power On/Off Switch
R1: RJ45 Giga LAN(6
pieces)
R2: Power LED(1 piece)
R3: HOD LED(1 piece)
R4: Power supply socket(12V DC IN)
RS: Holes for WLAN antennas
A
and
computer
vertically.
run
With
without the
horizontal
rubbe
us ,
feet.
NE
Notice: The computer can be
e
operated
VER let
horizontally
the
『
D. Mainboard
GREEN
IT
©
三
CE
