manualshive.com logo in svg

EFI E-46A, Installation And Service Manual, Page: 58 / 134

Share
Download
EFI E-46A Installation And Service Manual Download Page 58

58

Installation and Service Guide Color Controller E-46A

Replacing parts

The E-46A is shipped from the factory with a standard board configuration. If optional components have been 

installed, see the documentation that accompanies the particular option kit.

Printer interface board

The printer interface board provides the print interface between the E-46A and the printer. The printer interface board 

processes the image data and sends it to the printer through the printer interface cable. It is installed in PCIE x16 slot 

on the motherboard.

Figure 32:

Printer interface board

To remove the printer interface board

1

Shut down and open the E-46A (see 

page 51

). 

To remove the printer interface board, you must remove the left panel.

2

Remove the printer interface cable that connect the printer interface board and the printer.

3

Remove the board mounting bracket screw that attaches the printer interface board to the chassis.

4

Remove the printer interface board from the chassis.

Grasp the printer interface board at the front and back edges and gently pull the board straight out of its 

motherboard connector. 

5

Place the printer interface board in an antistatic bag.

To replace the printer interface board

1

Insert the board into the PCIE x16 slot on the motherboard (see 

Figure 33

 on page 61).

The component side of the interface board must face down, toward the base of the chassis. The interface board 

connector is keyed to fit only one way. When reseating the board, be careful to not disturb any motherboard cables 

that are installed nearby.

1

OFF/ON switch for power synchronization

4

J102 connector for power SW/LED cables from Fiery QuickTouch

2

Type B USB port connector for power synchronization

5

J103 connector for cable with keyed connectors

3

PCIE x16 connector

2

3

1

4

5

Summary of Contents for E-46A







































































































































Reviews:

No comments