EFI E-45 Installation And Service Manual Download Page 36

Page: 36 / 126

Installation and Service Guide: Color Controller E-45

Using the E-45

•

Reboot system: shuts down all Fiery server software and reboots the system.

•

Restart Server: resets the Fiery server software, but does not reboot the entire system.

•

Brightness: sets the brightness level of the Fiery QuickTouch screen.

Figure 16:

Quick options menu

Using the printer touch panel

The

“EFI Fiery”

icon of the printer touch panel allows you to interact with the E-45 from the printer. The menus provide

access to many of the same options available from Command WorkStation.

Figure 17:

The printer touch panel

To access to the Fiery screen on the printer touch panel

Press

Home

button on the printer touch panel.

Main

Waiting Jobs:

Idle

Paper Tray Status:

Document 3

Document 4

Document 1

Document 2

Printed Jobs:

Job List

Tools

Suspend Printing

Resume Printing

Summary of Contents for E-45































































































































Search results

Summary of Contents for E-45

Reviews:

EFI E-45, Installation And Service Manual, Page: 36 / 126

Search results

Summary of Contents for E-45

Reviews: