manualshive.com logo in svg

EFI E-45, Installation And Service Manual, Page: 120 / 126

Share
Download
EFI E-45 Installation And Service Manual Download Page 120

Specifications

This section provides an overview of the E-45 features, specifications, and safety certifications.

Hardware features

•

Intel Core i5-6500 quad core 3.2GHz CPU (up to 3.6GHz with Turbo Boost enabled)

•

Memory: 8GB (2

x

4GB)

•

An RJ-45 connector for 10BaseT/100BaseTX/1000BaseT Mbs connectivity over twisted pair cable (upper port)

•

1TB hard disk drive standard

•

Built-in DVD drive

Physical specifications

•

Operating Environment:

•

Temperature: +5

°

C to +40

°

C

•

Relative Humidity: 10%-85% (non-condensing)

•

Power Supply Voltage/Frequency Input: 100-240V @ 50-60Hz

•

Power Supply Current Input: 100V @ 6A Max.; 240V @ 3A Max.

•

Rated Power Consumption: 350W

•

Dimensions (Depth x Height 

x

 Width):

46.36 cm (18.25 in.) 

x

 52.71 cm (20.75 in.) 

x

 23.50 cm (9.25 in.)

•

Weight: 16.56 kg (36.5 lb.)

Networking and connectivity

•

Supports AppleTalk and TCP/IP protocols simultaneously.

Note:

AppleTalk is supported only for downloading fonts.

Safety and emissions compliance

The E-45 has been certified to meet or surpass the following government standards:

Safety approvals

•

IEC 60950-1:2005 (Second Edition) + Am 1:2009 + Am2:2013 and  IEC 62368-1:2014 (Second Edition) 

Summary of Contents for E-45































































































































Reviews:

No comments