EFI E-36A Installation And Service Manual Download

Page: 37 / 129

Installation and Service Guide: Color Controller E-36A

Using the E-36A

•

Brightness: sets the brightness level of the Fiery QuickTouch screen.

Figure 17:

Quick options menu

Using the E-36A from printer operation panel

The

“Fiery”

icon on the printer operation panel allows you to interact with the E-36A from the printer. The menus

provide access to many of the same options available from Command WorkStation

Figure 18:

The printer operation panel

To access the E-36A from printer operation panel

Press the

Home

button on the printer operation panel.

Main

Waiting Jobs:

Idle

Paper Tray Status:

Document 3

Document 4

Document 1

Document 2

Printed Jobs:

Job List

Tools

Suspend Printing

Resume Printing

Summary of Contents for E-36A


































































































































Search results

Summary of Contents for E-36A

Reviews:

Related manuals for E-36A

Brands by name

Popular brands

EFI E-36A, Installation And Service Manual

Search results

Summary of Contents for E-36A

Reviews:

Related manuals for E-36A

Brands by name

Popular brands