manualshive.com logo in svg

Edwards EXC120, Instruction Manual

Share
Download
Edwards EXC120 Instruction Manual Download Page 33

© Edwards Limited 2008. All rights reserved. 

Page 25

Edwards and the Edwards logo are trademarks of Edwards Limited.

Installation

D396-14-880 Issue J

Figure 8 - Schematic diagram of EXC120 & EXC120E Controller electrical connections

1. External electrical supply
2. Earth (ground)
3. Electrical supply connector
4. Electrical supply isolator
5. Front panel Heater switch *
6. Bakeout band fuse *
7. Rear panel bakeout band connector *
8. Bakeout band *
9. Backing pump
10. Backing pump relay *
11. Rear panel backing pump relay connector *
12. Rear panel Active gauge connector
13. Active gauge

14. Speed indicator
15. Logic interface connector
16. External SYS Interlock switch
17. External TMP Interlock switch
18. External Remote Standby switch
19. External Remote Start/Stop switch
20. TMP Normal output (normally open)
21. TMP Fail output (normally closed)
22. Not used
23. Vent-valve
24. Air-cooler
25. Remote indicator equipment

A. Vacuum and control system
B. EXC Controller

L. Live electrical supply
N. Neutral electrical supply
E. Earth (ground) electrical supply

*

Not available on the EXC120E Controller.

Summary of Contents for EXC120























































Reviews:

No comments

Brands by name

Popular brands

Load more brands