manualshive.com logo in svg

Edwards E1M40, Instruction Manual

Share
Download
Edwards E1M40 Instruction Manual Download Page 49

© Edwards Limited 2007. All rights reserved. 

Page 43

Edwards and the Edwards logo are trademarks of Edwards Limited.

Sp

ar

es

 a

nd

 a

cc

es

so

rie

s

A344-02-880 Issue J

7.4.9

Oil-level monitor

The oil-level monitor (see 

Figure 12

, item 7) fits in place of the existing oil-level sight-glass and bezel. The monitor 

provides a switching facility which you can use to activate an alarm or other device. You still have the normal visual 
indication of the oil-level.

7.4.10

Solenoid-operated gas-ballast control valve

The solenoid-operated gas-ballast control valve (see 

Figure 12

, item 2) gives you automatic or remote control of 

gas-ballast. You can connect the valve to shut off gas-ballast when the pump is switched off and so prevent air from 
returning to the system.

Product

Item Number

OLM100 Oil Level Monitor

A504-33-000

Product

Item Number

EBV100S Solenoid-Operated Gas-Ballast

A500-18-930

Control Valve for E1M40 and E1M80
EBV300D Solenoid-Operated Gas-Ballast

A500-17-930

Control Valve for E2M40 and E2M80

Summary of Contents for E1M40

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands