manualshive.com logo in svg

Edwards CXS, Instruction Manual, Page: 10 / 40

Share
Download
Edwards CXS Instruction Manual Download Page 10

D397-53-880 Issue C

Page 2

© Edwards Limited 2016. All rights reserved.

Edwards and the Edwards logo are trademarks of Edwards Limited.

Introduction

1.2

Outline description

The GXS and CXS Profibus Module provides a Profibus DP V0 slave interface for Edwards GXS and CXS pumps. The
module communicates with the pump using the RS232 interface. Commands received from the Profibus network are
relayed to the pump. Data from the pump is stored in the module and transmitted over the Profibus network when
requested. The pumps provide the DC power for the module. The front panel of the module has four LEDs which
indicate the status of the module and the Profibus network. The Profibus slave address is set using rotary switches.
The back panel of the module has a 9-way 'D' connector for the Profibus network, a 9-way 'D' connector for the RS232
link to the pump and a power connector.

WARNING

Edwards take no responsibility for damage or injury caused by improper use of the equipment.

WARNING

This equipment provides remote control of an Edwards pump. You must refer to the safety 
information in the pump instruction manual.

WARNING

This unit should not be relied upon for safety related functions.

Summary of Contents for CXS









































Reviews:

No comments