background image

14

Safety

The equipment should be installed by an audio visual technician observing 'good electrical 

and audio practice' at all times and following all the instructions within this document� 
 

Only use the power adapter supplied with the unit� If the power adapter or  

 

cable is damaged, replace with a genuine Univox part�

 

Power adapter must be connected to a mains outlet close to the amplifier and  

easily accessible� Connect the power to the amplifier before connecting to the network, 

otherwise there is a risk of sparking� 
The installer is responsible for installing the product in a way that may not cause risk of 

fire, electrical malfunctions or danger for the user� Do not cover the power adapter or loop 

driver� Only operate the unit in a well ventilated, dry environment�
   

Do not remove any covers as there is a risk of electric shock� There are no user  

 

serviceable parts inside� Refer servicing to qualified personnel� Please observe  

 

that the product warranty does not include faults caused by tampering with the  

 

product, carelessness, incorrect connection/mounting or maintenance�

Warranty

This loop driver is supplied with a 5 year (return to base) warranty�
Misuse of the product in any way including but not limited to:
•  Incorrect installation
•  Connection to non-approved power adapter
•  Self oscillation resulting from feedback
•  Force majeure e�g� lightning strike
•  Ingress of liquid 
•  Mechanical impact
will invalidate the warranty�

Maintenance and care

Under normal circumstances the product does not need any special maintenance� 
Should the unit become dirty, wipe it with a clean damp cloth� Do not use any solvents or 

detergents�

Summary of Contents for 223000

















Reviews: