Edimax AR-7288WnA Manual Download Page 1

 

 

 

 

COPYRIGHT 

 

Copyright 

 Edimax Technology Co., Ltd. all rights reserved. No part of this 

publication may be reproduced, transmitted, transcribed, stored in a retrieval 

system, or translated into any language or computer language, in any form or 

by any means, electronic, mechanical, magnetic, optical, chemical, manual or 

otherwise, without the prior written permission from Edimax Technology Co., 

Ltd. 

 

Edimax Technology Co., Ltd. makes no representations or warranties, 

either expressed or implied, with respect to the contents hereof and 

specifically disclaims any warranties, merchantability, or fitness for any 

particular purpose. Any software described in this manual is sold or licensed 

as is. Should the programs prove defective following their purchase, the buyer 

(and not this company, its distributor, or its dealer) assumes the entire cost of 

all necessary servicing, repair, and any incidental or consequential damages 

resulting from any defect in the software. Edimax Technology Co., Ltd. 

reserves the right to revise this publication and to make changes from time to 

time in the contents hereof without the obligation to notify any person of 

such revision or changes. 

 

The product you have purchased and the setup screen may appear slightly 

different from those shown in this QIG. For more information about this 

product, please refer to the user manual on the CD-ROM. The software and 

specifications are subject to change without notice. Please visit our website 

www.edimax.com for updates. All brand and product names mentioned in 

this manual are trademarks and/or registered trademarks of their respective 

holders. 

 

Edimax Technology Co., Ltd. 

Add: No. 3, Wu-Chuan 3

rd

Tel: +886-2-77396888 

 Rd., Wu-Ku Industrial Park, New Taipei City, Taiwan 

Email: 

[email protected]

 

Summary of Contents for AR-7288WnA
































































































Reviews: