Edic Endeavor 9000I-HSH Owner'S/Operator'S Manual Download Page 4

UNPACKING YOUR NEW ENDEAVOR:

When your equipment is delivered, check the carton 

carefully for signs of rough handling. If the ENDEAVOR 

is damaged, notify the carrier immediately and request 

an inspection. Be sure to keep the carton, packing in-

serts, packing lists and carrier’s receipt until the inspec-

tor has verified your claim.

EDIC’s liability ceases when the carrier picks up the 

shipment. However, our customer service staff will be 

happy to furnish any information needed in connection 

with the claim and will attempt to expedite a resolution.

 

PLEASE READ BEFORE OPERATING YOUR 

NEW ENDEAVOR:

Read the manual carefully and completely before at-

tempting to operate the unit. This manual has important 

information for the use and safe operation of the ma-

chine. Keep this manual handy at all times.

This equipment has been engineered and manufactured 

to provide excellent performance and service. To ensure 

that your equipment will continue to perform as intend-

ed:

•  Maintain equipment regularly- following the sug-

gested maintenance schedule provided.

•  Use only original EDIC parts when servicing.

•  Operate equipment with care.

All information and specifications printed in the man-

ual are current at the time of printing; however because 

of EDIC’s policy of continual product development, we 

reserve the right to make changes at any time without 

notice.

 

FAILURE TO COMPLY WITH THE FOLLOWING 

WARNINGS AND INSTRUCTIONS MAY POSE A 

HAZARD AND WILL VOID THE WARRANTY.

WARNING:

 

•  This is not a toy. Keep away from children.

•  Always read and understand your chemical’s MSDS (Ma-

terial Safety Data Sheet) before use.

•  This extractor is not designed to handle or use combus-

tible/volatile substances such as gasoline or kerosene, in, 

on, or near the equipment. The use of such materials will 

cause extreme hazardous condition.

•  Make sure the extractor has all water filters in place.

•  Do not allow high pressure spray stream to remain in one 

fixed location as surface damage may occur.

•  Check that all spray nozzles are securely fastened. Loose 

nozzles could be ejected from equipment at high speeds.

•  Prevent burns by wearing gloves or using a barrier to 

remove hot quick disconnects.

•  Use caution with ejected liquid or chemicals. High pres-

sures and temperatures could be hazardous to nearby peo-

ple or surroundings.

•  All servicing of EDIC equipment should be performed 

only by EDIC authorized service centers.

•  Do not use replacement parts other than those specified in 

the parts list. Equipment performance could be affected if 

substitutions are made. Use of no-EDIC parts will void the 

warranty.

 

•  When using an extension cord, use only a 3-prong conduc-

tor grounding cord-12 gauge wire or heavier. Do not use 

extension cords longer than 25FT.

•  To avoid electric shock, do not expose the unit to rain 

or snow. Store indoors in a heated location only. Do not 

expose machine to freezing temperatures.

•  Do not use the machine for dry vacuuming.

•  Use defoamer at all times to prevent damage to the vacu-

um motor.

•  Do not use water in excess of 130°F (54°C) in the solution 

tank

•  To prevent seal damage and chemical build-up to the 

pump system, run clean water through the solution lines 

after each day’s use.

•  Use only commercially available carpet cleaning solutions 

and defoamer intended for use with machines of this type. 

Do not use dyes, bleaches, ammonia, or other additives. 

•  The use of powdered cleaning solution, if not diluted 

properly, may result in damage to the pump. Powdered 

chemical is not recommended. If powdered chemicals 

are used, premix in a separate container before placing in 

the solution tank. Any damage resulting from powdered 

chemical will void the warranty.

•  Do not pull machine by the power cord. Always unplug by 

grabbing the plug and pulling, do not unplug by pulling 

the power cord.

•  Periodically inspect cord for damage. Do not use damaged 

cords. Connect only to properly grounded outlets.

•  Keep hair, fingers, loose clothing, and body parts away 

from moving parts and openings.

•      Turn off all controls before disconnecting machine
•  Do not use without vacuum pre-filter bag in place.

3

Summary of Contents for Endeavor 9000I-HSH


























Reviews: