background image

 

 

Handbook 

ECW-5210-L Enterprise Access Point 

ENGLISH 

 

ii 

CE CAUTION 

Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for   

European Community, Switzerland, Norway, Iceland, and Liechtenstein   

Model: ECW5210-L   

For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and 

hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement. 

• Radio: EN 300.328

:

 

• EMC: EN 301.489-1, EN 301.489-17,   

• EMC: EN 55022

 

Class B, EN 55024

:

+ A1 + A2

 

including the followings: 

      EN 61000-3-2, EN 61000-3-3. 

      EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,   

      EN 61000-4-5, EN 61000-4-6, EN 61000-4-11 

• Safety: EN 60950-1 + A11, 

 

Caution:

   

 

This  declaration  is  only  valid  for  configurations  (combinations  of  software,  firmware,  and  hardware) 

provided and supported by Edgecore Networks Corporation. The use of software or firmware not provided 

and  supported  by  Edgecore  Networks  Corporation.  may  result  in  the  equipment  no  longer  being 

compliant with the regulatory requirements.   

European  standards  dictate  maximum  radiated  transmit  power  of  100mW  EIRP  and  frequency  range 

2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. 

 

Taiwan NCC Statement 

 

 

根據 NCC 低功率電波輻射性電機管理辦法  規定:

 

第十二條

 

經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或

變更原設計之特性及功能。

 

第十四條

 

 

 

低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善
至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受
合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

 

在 5.25 ~ 5.35 秭赫頻帶內操作之無線資訊傳輸設備,限於室內使用。

 

 

 

減少電磁波影響,請妥適使用

Summary of Contents for ECW5210-L

















Reviews: