Catalog #67082, 67083, 67092, 67093
©2006 Edelbrock Corporation
Page 1 of 2
Brochure #63-67082
Rev. 5/06 - DA/mc
®
TUBULAR EXHAUST SYSTEM
Vehicle Applications: See Below
Catalog #67082, #67083, #67092, #67093
INSTALLATION INSTRUCTIONS
Please study these instructions carefully before installing your new
Tubular Exhaust System (TES). If you have any questions, please
contact our
Technical Hotline at : 1-800-416-8628
from 7 am - 5pm, Monday-Friday, Pacific Standard Time or e-mail us at
. Please fill out and mail your warranty card.
Applications:
Catalog #s 67082, #67083 - 1996-1997 Chev./GMC S-10, S-15 Pick-Up, 4.3L V6 2WD with Auto Transmission
Catalog #s 67092, #67093 - 1996-1997 Chev./GMC S-10, S-15 Pick-Up, Blazer, Jimmy, 4.3L V6 4WD, Auto Transmission
TUBULAR EXHAUST SYSTEM:
These components are designed as a system to improve the exhaust efficiency of the GM C.P.I.
(Central Port Injection) 4.3L V6 engine. A performance gain can be expected by the installation of the system. This system requires
no welding for installation and retains all O.E.M. emissions equipment.
Suggested Tools Needed for Installation:
This vehicle has some metric fasteners.
❑
3/8" ratchet socket set with extensions and universal 13mm and 15mm swivel sockets
❑
Combination set of open-end wrenches
❑
Jackstands, screwdrivers, pliers, crescent wrench, etc.
❑
Liquid penetrant, (GM #1052627) anti-seize compound (GM #5613695)
SPECIAL NOTICE:
This Edelbrock Tubular Exhaust System has received an Executive Order number (E.O.#) from the California Air
Resources Board (C.A.R.B.) making it legal for street use in all 50 states. To assist you with emission equipment certification, we
have included a silver fan shroud decal to help testing personnel verify the this part is a legal replacement on the vehicle for which
it is cataloged. The adhesive-backed decal should be affixed next to the existing emission and engine specifications decal. Do not
cover any part of your original emission decal.
WARNING:
The use of "Thermal Wrap" or any aftermarket coating process
will void the warranty
on your Edelbrock Tubular
Exhaust Systems. Those products can cause excessive heat and moisture buildup resulting in corrosion and failure of the system.
NOTE:
High temperature spark plug wires and boots are recommended to withstand heat from T.E.S.
IMPORTANT NOTE:
Proper installation is the responsibility of the installer. Improper installation will void warranty and may result in
poor performance and engine or vehicle damage.
INSTALLATION INSTRUCTIONS
DISASSEMBLY
1.
Disconnect battery negative cable from battery.
2.
Raise vehicle and support with jackstands.
3.
Use penetrating oil on all nuts and bolts to be removed.
This will prevent the possibility of broken or stripped nuts
and bolts.
4.
Remove O2 sensors and unbolt exhaust crossover pipe
from manifolds.
5.
Unbolt and remove crossover pipe assembly.
6.
Lower vehicle and remove air cleaner assembly.
7.
Remove all spark plugs.
8.
Unbolt and remove right side exhaust manifold.
9.
Unbolt dipstick bracket from cylinder head, but do not
remove dipstick.
10. Remove EGR tube from left manifold.
11. Remove cross bolt from steering shaft and slide lower
section of shaft down off of upper shaft.
12. Unbolt and remove left exhaust manifold.
13. Remove EGR adapter from left manifold.
ASSEMBLY LEFT SIDE
1.
Install EGR adapter in new manifold.
2.
Start rear manifold bolt with gasket, lock and flat washer
in place, and screw in leaving just enough space to slide
manifold into position.
NOTE:
Be sure spark plug clips do
not interfere with manifold surface.
