manualshive.com logo in svg

Eddyfi Technologies INUKTUN VERSATRAX 100, User Manual, Page: 39 / 41

Share
Download
Eddyfi Technologies INUKTUN VERSATRAX 100 User Manual Download Page 39

 

                               

Versatrax 100™ 

 

 

Document: UMDT013103.docm  

Revision: A10 

Created by: KJB 

Date: 26 Sep 2019 

3070984-A10 

Source Location: C:\ePDM\ISLEng\products\dt-versatrax100mkii\manuals\UMDT013103.docm

 

 

Page 39 of 41 

 

 

  

    

    

   

   

   

   

  

  

Us

er

 M

an

u

al

 

Parts and Repairs 

Ordering Parts/Customer Service 

Spare and/or replacement parts are available for your product and can be ordered directly from your local 
office. 

When ordering parts always make sure to quote the sales order acknowledgement (SOA) number and/or 
the serial number of the system component in question.  

Inuktun Services Ltd. (Canadian Headquarters and Manufacturing Location) 

2569 Kenworth Road, Suite C 

Nanaimo, BC, V9T 3M4 

CANADA 

TF 1.877.468.5886 

T +1.250.729.8080 

[email protected] 

www.eddyfitechnologies.com 

Eddyfi Technologies 

– US (American Authorized Distributor and Service Centre) 

812 W 13th Street 

Deer Park, TX, 77536 

USA 

T +1.281.542.3292 

[email protected] 

www.eddyfitechnologies.com 
 

 

Summary of Contents for INUKTUN VERSATRAX 100










































Reviews:

No comments