background image

 

Spectrum 90

™ Camera 

 

Document: UMAD007298.docm  

Revision: A10 

Created by: KJB 

Date: 27 Sep 2019 

IPN: 3041348-A10  

Source Location: C:\ePDM\ISLEng\products\ad-spectrum90\manuals\UMAD007298.docm

 

 

Page 19 of 19 

 

User Ma

nual

 

Limited Warranty Policy 

Eddyfi Technologies will repair or replace, at its expense and at its option, any system or component, 
subject to the limitations and / or exclusions specified herein, which in normal use has proven to be 
defective in workmanship or material provided that, within one (1) year of the purchase date, the original 
purchaser returns the product prepaid, accompanied by proof of purchase, from a sales agent authorized 
by Eddyfi Technologies, and provides Eddyfi Technologies with reasonable opportunity to verify the 
alleged defect by inspection. 

Warranty Limitations and/or Exclusions: 

1.  This warranty does not apply to light bulbs. 

2. 

Batteries, fuses, transistors, integrated circuit modules (IC’s), voltage regulating devices and electrical 
plugs and / or connectors are warranted to be free from defects in material and workmanship for a 
period of ninety (90) days from the date of shipment to the original purchaser. 

3.  Any article purchased from, but not manufactured by, Eddyfi Technologies is sold with only such 

warranties as are made by the manufacturer therein. Eddyfi Technologies only warrants that it has 
title thereto, free of all liens or encumbrances. 

4.  This warranty does not apply to units which are damaged by connection to improperly wired AC 

receptacles. 

5.  Track belts, tethers, view ports and other components subject to wear through abrasion are 

warranted to be free from defects in material and workmanship for a period of ninety (90) days from 
the date of shipment to the original purchaser. 

6.  Any damage caused by failure to observe proper packing or to observe instructions for operation and 

maintenance as contained in the Instruction Manual furnished with the equipment, by accident in 
transit or elsewhere, will not be covered by the warranty. 

7.  Repairs are warranted for 90 days. 

Eddyfi Technologies 

may require that certain components may be returned, prepaid, to a manufacturer’s 

authorized station for inspection and repair or replacement. 

Eddyfi Technologies will not be responsible for any asserted defect which has resulted from Acts of God, 
normal wear, misuse, abuse, improper configuration, repair, or alteration made, or specifically authorized 
by, anyone other than a representative of Eddyfi Technologies authorized to do so. The giving of, or 
failure to give, any advice or recommendation by Eddyfi Technologies shall not constitute any warranty 
by, or impose any liability on, Eddyfi Technologies. 

The foregoing constitutes the sole and exclusive remedy of the purchaser and the exclusive liability of 
Eddyfi Technologies and is in lieu of any and all other warranties, express, implied or statutory as to 
merchantability, fitness for purpose sold, description, quality productiveness, or any other matter. Under 
no circumstances shall Eddyfi Technologies be liable for special, incidental or consequential damages, or 
for delay in performance of this warranty. 

 

Summary of Contents for INUKTUN SPECTRUM 90




















Reviews: