Ecotechnics Reflectors: Air-Cooled Diamond
Congratulations on purchasing your
Before you switch on any part of the system, please make sure you get the most from the reflector by taking a minute
to read this important information.
Ecotechnics Air-Cooled Diamond Reflector.
Installation
Troubleshooting
Guarantee
Air-Cooled Diamond
If the reflector has a protective film attached to it, remove it
Mount the reflector in a suitable position. Holding the base of the
lamps (if you hold them by the glass tubes they may shatter !), screw
them into the reflector’s sockets firmly to ensure a good electrical
contact.
When the reflector is safely mounted and the lamps are installed
correctly, the unit can be switched on.
The Air-Cooled Diamond has an adjustable lamp holder which you
have the option to move the bulb to the centre of the reflector
depending on the length/type of bulb you are using, thus you can
maximise the reflecting capability of light produced.
For best usage Air-Cooled Diamond Reflector’s have 150mm spigot
so that you can take advantage of ducted cooling on the Diamond
Reflector.
In the unlikely event that you find fault with this product, please
contact your supplier. All Ecotechnics reflectors carry a one year
guarantee (terms & conditions apply), excluding faulty fuses and
tampering.
Ecotechnics
Reflectors
Next Generation
Technology Today
www.ecotechnics.co.uk
If the Lighting system fails to start:
1.Check your ballast to make sure that is operating correctly
2.Check the bulb to make sure it is working correctly and has not
blown or is damaged for example
3.Check your electric supply, plugs and sockets.
4.Switch off your lighting system, wait for the lamps to cool and then
remove them and screw them back in again firmly. Switch the unit
back on and if the lamps still fail, contact your supplier.
Note:
In most cases a lighting failure is due to a defective ballast or bulb.
Safety Advice
The Lamp will get hot during use. Leave it to cool before touching it
and never touch it while it is switched on!
When connecting / disconnecting all cables, grasp the connector
itself—never pull on the cable. This way you will avoid causing
shorts, or damage to the cable’s internal elements.
Do not excessively twist or bend the power cord, or place heavy
objects on it. Doing so can damage the cord, producing severed
elements and short circuits. Damaged cords are fire and shock
hazards!
In households with small children, an adult should provide
supervision which is essential for the safe operation of any electrical
appliances in the home.
All cords and cables should be placed so they are out of the reach of
children.
Try to prevent cords and cables from becoming entangled.
Before moving the unit, disconnect the power cable from the mains
supply and any cords coming from external devices.
Never handle an AC adaptor or electrical plugs with wet hands when
plugging into, or unplugging from, an outlet or this unit.
Before cleaning the unit, turn off the power and unplug the AC
adaptor from the outlet.
Do not force the unit’s power-supply cord to share an outlet with an
unreasonable number of other devices.
Be especially careful when using extension cords—the total power
used by all devices you have connected to the extension cord’s outlet
must never exceed the power rating (watts/amperes) for the
extension cord.Excessive loads can cause the insulation on the cord
to heat up and eventually melt through.
Protect the unit from strong impact.(Do not drop it!)
Before using the unit in a foreign country, consult with your retailer or
an authorized distributor.
Whenever you suspect the possibility of lightning in your area,
disconnect the unit from the power outlet.
Do not attempt to repair the unit, or replace parts within it. Refer all
servicing to your retailer or an authorized distributor.
When moved from one location to another where the temperature
and/or humidity is very different, water droplets (condensation)
may form inside the unit. Damage or malfunction may result if you
attempt to use the unit in this condition. Therefore, before using
the unit, you must allow it to stand for several hours, until the
condensation has completely evaporated.
---- ALWAYS OBSERVE THE FOLLOWING ----
