manualshive.com logo in svg

EcoFasten Clickfit, Installation Manual

Share
Download
EcoFasten Clickfit Installation Manual Download Page 4

VERSION: v3.0

REVISION DATE: 12/2/22

 

INSTALLATION GUIDE

INT

RO

DU

CTI

ON

PAGE 

03

INTRODUCTION

This manual describes the installation of the ClickFit mounting system for photovoltaic 

modules on steep-slope roofs. Described within are details for composition shingle and tile, 

attachments for ClickFit System.  Other roof types as well as all other installation manuals 

can be found for download at www.EcoFastenSolar.com.

GENERAL INSTALLATION CONDITIONS

Failure to observe the requirements in this document can lead to the exclusion of all 

guarantees and product liability. EcoFasten Solar reserves the right to amend this document 

without prior notice.

STABILITY & CONDITION OF THE ROOF

The roof must be in good condition and strong enough to support the weight of the modules, 

including the additional equipment, wind and snow loads. When in doubt, consult with the 

engineer of record, and/or the local building inspector.

APPLICATION RANGE OF CLICKFIT

Refer to Compatibility module list at the end of this document. Please refer to the Ecofasten 

ClickFit span tables for system structural certification and allowable spans.

WARRANTY

Guarantee according to the warranty conditions and general terms and conditions of 

EcoFasten Solar. These conditions can be found on the website at www.EcoFastenSolar.com.

LIABILITY

EcoFasten Solar cannot accept any liability whatsoever for damage or injury caused by 

not taking adequate safety precautions or (accurately) following the instructions given, or 

resulting from negligence during the installation of the product and any corresponding 

accessories specified in this document.

Summary of Contents for Clickfit










































Reviews:

No comments

Brands by name

Popular brands

Load more brands