Ecoer EODA18H-2436 Service Manual Download Page 20

Page: 20 / 82

Manufacturer reserves the right to change specifications or designs without notice.

10.2019

ESI (Ultra) Service Manual

www.ecoer.com

17/68

2.3

Field Setting

2.3.1

Default display

LED on main control board can display the operating status of outdoor unit (ODU).

SEG1 SEG2 SEG3

7 segment display instructions

SEG1:

Normally blank, but it displays codes “1~9” accordingly if there is damaged sensor and demand

control requirement.

SEG1 Code

Description

Time

Software is updating through IoT device

About 5 min

High pressure sensor (HP) fault backup running

7 Days

Low pressure sensor (LP) fault backup running

7 Days

Compressor discharge temperature sensor (TD) fault backup running

7 Days

IPM module temperature sensor (TF) fault backup running

7 Days

Ambient temperature sensor (TA) fault backup running

120 Days

Defrost sensor (TH) fault backup running

90 Days

Compressor suction temperature sensor (TS) fault backup running

120 Days

Liquid line temperature sensor (TL) fault backup running

120 Days

IoT demand response

SEG2:

Normally blank, but it will display code accordingly as below if outdoor unit is running under

limited condition.

SEG2 Code

Description

Running under high pressure (HP) limit

Running under low pressure (LP) limit

Running under discharge temperature (TD) limit

Running under IPM module temperature (TF) limit

Running under compressor current limit

SEG3:

It displays outdoor unit’s operation mode.

SEG3 Code

Description

Stop without running signal (Y signal=OFF)

Ready to start-up after receiving running signal (Y signal=ON)

*Note

Cooling mode

Heating mode

Oil return

Defrost

Manually defrost

AUTO charge mode in cooling

Pump down

Note: Compressor waits 3~6 minutes to restart.

Summary of Contents for EODA18H-2436



















































































Search results

Summary of Contents for EODA18H-2436

Reviews:

Ecoer EODA18H-2436, Service Manual, Page: 20 / 82

Search results

Summary of Contents for EODA18H-2436

Reviews: