Eclipse TD508MK3 Owner'S Manual Download Page 22

− 8 −

ENGLISH

GERMAN

FRENCH

IT

ALIAN

SP

ANISH

■ 

Maintenance

Before cleaning, be sure to turn off the power supply for all connected equipment and disconnect the power cords
from the electrical outlets. Remove any dirt from the unit by lightly wiping with a soft dry cloth.

If required moisten the cloth to remove surface dirt, then dry with
a soft cloth.
Do not use gasoline or thinners, etc. on this unit as it may damage
the cabinet.

■ 

Problems during Operation of the Unit

During operation, the unit may stop working properly if it suffers from significant external disruption (impact shock, 
static electricity, voltage fluctuation caused by lightning, etc.) or is operated incorrectly.

In this situation, turn the amplifier power to switch to the “Off” position.
Turn it back on again and check if normal operation has resumed. (If a problem persists, please contact our Service 
Centre)

■ 

Notice for WEEE directive

In accordance with the European Directive 2002/96/EC (for Waste Electric and Electronic Equipment=WEEE), this 
product, which is labeled with crossed-out wheeled bin, may not be disposed of with household waste in member 
states of the EU. 
WEEE : Waste Electrical and Electronic Equipment 
When disposing of this product in an EU member state, dispose properly in 
accordance with the laws of that state, for example by returning it to the distributor. 
WEEE has the potential effects on the environment and human health as a result of 
the presence of hazardous substances. 
You can contribute to eliminate these effects and to enhance reuse/recycle/ other 
forms of recovery by your cooperation.

■ 

Specifications

Specifications and appearance are subject to change without prior notification.

 

●TD508MK3

 

Driver diameter

  :

φ

8cm

 

Degaussing

   :

Degaussing design (JEITA)

 

Allowable input

  :

Rated 15 W / Maximum 30 W

 

Impedance

   

 

Outer dimensions

W180×D268×H289 (mm)

 

Weight

     :

Approximately 3.5kg

 

●TD510MK2

 

Driver diameter

  :

φ

10cm

 

Degaussing

   :

Degaussing design (JEITA)

 

Allowable input

  :

Rated 25 W / Maximum 50 W

 

Impedance

   

 

Outer dimensions

W255×D381×H391 (mm)

 

Weight

     :

Approximately 9.5kg

Care / Specifications

Care / Specifications

Summary of Contents for TD508MK3



























Reviews: