ECKELMANN VDD 500 Operating	 Instruction Download Page 21

 

 

08.11.2022

21/23

6 Decommissioning and Disposal

6.1  Außerbetriebnahme / Demontage

The dismantling of the equipment may only be performed by authorised and trained personnel.

6.2  Disposal

DANGER

Warning of dangerous electrical voltage! Danger to life - danger of electric shock!

During dismantling, the same safety instructions and hazard warnings must be observed as for 
installation, putting into service and maintenance, see chapter Safety instructions.

ATTENTION

For dismantlement, follow the steps for assembly in reverse order, see chapter Installation and Start-
Up.

NOTICE

WEEE Reg. No.
DE 12052799

Negative consequences for humans and the environment possible through 
environmentally unfriendly disposal! 

The symbol for the separate disposal of electrical and electronic equipment represents 
a crossed-out wheeled trash bin and indicates that an electrical or electronic 
equipment marked with this symbol may not be disposed of with household waste at 
the end of its service life, but must be taken for separate disposal by the end user.

In accordance with the contractual agreement, the customer is obliged to dispose 
of electrical and electronic waste in compliance with the statutory regulations based 

on the „Directive 2012/19/EU of the European Parliament on waste electrical and 
electronic equipment“.

Dispose the packaging, the product and its components in an environmentally 
friendly manner at the end of their service life. Follow the national guidelines and 
laws that apply to you.

Users have the option of returning a B2B device distributed by us to us at the end of its 
service life. Please contact your customer service representative at Eckelmann AG to 
arrange for the device to be taken back and disposed of properly. Please inform 
yourself about the local regulations for the separate disposal of electrical and 
electronic products and batteries. Further information on the Electrical and Electronic 
Equipment Act can be found at 

www.elektrogesetz.de

.

Summary of Contents for VDD 500
























Reviews: