background image

Echoflex Installation Guide

Vacancy Sensor

DIP Switch Settings

DIP switches on the sensor electronics provide for additional configuration
options including Use Custom Config, Vacancy Timeout, Enable/Disable PIR
detection LED, and the ability to restore the sensor to its factory defaults.

Switch #

Use

1

Unused (leave Off)

2

Enable/Disable Custom Config Mode

When “Custom Config” is set to Off (also known as Basic
configuration mode), local DIP switch settings for Vacancy
Timeout and Enable PIR LED are used. See

Configuration

on page 9

.

When “Custom Config” is set to On, all other local DIP
switch settings are ignored. Instead, the settings made by
the ElahoAccess App are used.

3 and 4

Vacancy Timeout

5 min = Switches 3 and 4 are Off

15 min = Switch 3 is Off and Switch 4 is On (default)

30 min = Switch 3 is On and Switch 4 is Off

Auto = Both switches are On (See

Vacancy Timeout on

page 10

.)

5

PIR Detection LED

When set to On (default), the occupancy detection LED
illuminates the lens when movement is detected.

When set to Off, the occupancy detection LED is disabled
unless the unit is in Walk Test mode.

6

Unused (leave Off)

7

Unused (leave Off)

8

Restore to Defaults at boot

When set to On and power is cycled to the sensor, the
unit restores to its factory default settings.

Off is the default setting.

Vacancy Sensor

Page 8 of 12

Echoflex

Summary of Contents for Elaho E-VAC













Reviews: