Echo SRM-410X Operator'S Manual Download Page 50

Page: 50 / 56

SPECIFICATIONS

SRM-410X

X7502168400

SPECIFICATIONS

MODEL

SRM-410

Length without cutter head

1,866 mm (73.5 in.)

Width

347 mm (13.7 in.)

Height

367 mm (14.4 in.)

Weight (dry) without cutter
head

7.4 kg (16.3 lb.)

Engine Type

Air cooled, two-stroke, single cylinder gasoline
engine

Bore

40 mm (1.58 in.)

Stroke

34 mm (1.34 in.)

Displacement

42.7cc (2.61 in.³)

Exhaust

Spark arrestor muffler or spark arrestor muffler with
catalyst

Carburetor

Diaphragm wth purge pump

Ignition System

Flywheel magneto, capacitor discharge ignition type

Spark Plug

NGK BPM7A (BPMR7A in Canada)– Gap 0.6 mm
(0.026 in.)

Fuel

Mixed (Gasoline and Two-stroke Oil)

Fuel/Oil Ratio

50:1

Gasoline

Use 89 Octane unleaded. Do not use fuel containing
methyl alcohol, more than 10% ethyl alcohol or 15%
MTBE. Do not use alternative fuels such as E15 or
E85.

Oil

ISO-L-EGD (ISO/CD 13738) and J.A.S.O. M345-
FD, two-stroke, air-cooled engine oil.

Fuel Tank Capacity

1 L (33.8 US fl. oz.)

Starter System

Automatic rewind starter

Clutch

Centrifugal type

Vibration Isolated System

Rubber cushion on engine mount (heavy duty).
Rubber grip on front handle.

Operating Rod

28.0 mm (1.1 in.) aluminum tube

Drive Shaft

8 mm (0.31 in.) steel shaft

Gear Case Ratio

1.33

Rotating Direction

Counterclockwise; viewed from top

Cutter Head

Speed Feed

450 LH nylon line head, line capacity

7.6 m (25 ft.)

Summary of Contents for SRM-410X

























































Search results

Summary of Contents for SRM-410X

Reviews:

Brands by name

Popular brands

Echo SRM-410X, Operator'S Manual

Search results

Summary of Contents for SRM-410X

Reviews:

Brands by name

Popular brands