manualshive.com logo in svg

Echo SRM-410X, Operator'S Manual

Share
Download
Echo SRM-410X Operator'S Manual Download Page 41

SRM-410X

MAINTENANCE

X7502168400

41

© 11/20 ECHO Incorporated

1.

Remove spark plug lead from 

spark plug, and remove muffler 

cover.

2.

Place piston at top dead center. 

Remove muffler (A) and heat 

shield (B).

3.

Use a wood or plastic scraping 

tool to clean deposits from 

cylinder exhaust port (C).

4.

Inspect heat shield, and replace if 

damaged.

5.

Install heat shield and muffler.

6.

Tighten muffler mounting bolts (or 

nuts) to 110-150 kgf•cm (95-130 

in•lbf).

7.

Install muffler cover and attach 

spark plug lead.

8.

Start engine, and warm to 

operating temperature.

9.

Stop engine, and re-tighten 

mounting bolts (or nuts) to 

specifications.

Carburetor Adjustment

Level 2.

When carburetor adjustment is completed, the cutting 
attachment should not move at idle, otherwise serious personal 
injury may result.

Engine Break-In

New engines must be operated a minimum duration of two tanks of fuel 

break-in before carburetor adjustments can be made. During the break-in 

period your engine performance will increase and exhaust emissions will 

stabilize. Idle speed can be adjusted as required.

High Altitude Operation

This engine has been factory adjusted to maintain satisfactory starting, and 

durability performance up to 330 m (1100 ft.) above sea level (ASL) (96.0 

kPa). To maintain proper engine operation above 330 m (1100 ft.) ASL the 

carburetor may need to be adjusted by an authorized service dealer.

A

B

C

Summary of Contents for SRM-410X

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands