manualshive.com logo in svg

Echo SRM-410X, Operator'S Manual

Share
Download
Echo SRM-410X Operator'S Manual Download Page 40

MAINTENANCE

SRM-410X

40

X7502168400

© 11/20 ECHO Incorporated

Exhaust System

Spark Arrestor Screen

Level 2.

Parts Required: Spark Arrestor Screen, Gasket

1.

Remove spark plug lead.

2.

Remove muffler cover (A).

3.

Place piston at Top Dead Center 

(TDC) to prevent carbon or dirt 

from entering cylinder.

4.

Remove spark arrestor screen 

cover (B), screen holder (C), 

gasket (D), and screen (E), from 

muffler body.

5.

Clean carbon deposits from 

muffler components.

Note:  When cleaning carbon 

deposit, be careful not to 

damage the catalytic 

element inside muffler.

6.

Replace screen if it is cracked, 

plugged, or has holes burned 

through.

7.

Assemble components in reverse order.

Exhaust Port Cleaning

Level 2.

Never use a metal tool to scrape carbon from the exhaust port. Do 
not scratch the cylinder or piston when cleaning the exhaust port. Do 
not allow carbon particles to enter the cylinder.

Parts Required: As needed: Heat Shield

A

E

D

C

B

Summary of Contents for SRM-410X

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands