manualshive.com logo in svg

Echo SRM-410X, Operator'S Manual

Share
Download
Echo SRM-410X Operator'S Manual Download Page 37

SRM-410X

MAINTENANCE

X7502168400

37

© 11/20 ECHO Incorporated

1.

Close choke (COLD START 

position). This prevents dirt 

from entering the carburetor 

throat when the air filter is 

removed. Brush accumulated 

dirt from air cleaner area.

2.

Remove air filter cover (A). 

Brush dirt from inside cover.

3.

Remove air filter (B) from case. 

Use care to prevent dirt and 

debris from falling into case. 

4.

Inspect filter element and seal. 

Replace filter if any of these 

problems are present:
• Air filter seal does not fit tightly against case
• Air filter seal is distorted, worn, or damaged
• Air filter element has holes or other damage
• Air filter element is saturated with dirt
• Air filter element is soaked with fuel mix

5.

If air filter is in good condition and can be cleaned and reused, lightly 

brush debris from air filter element, or blow filter element clean using 

low pressure (40 psi or less) compressed air directed at inside of filter.

When using compressed air, always direct air stream at inside 
surface of filter so dust and debris will be blown out of filter. Keep air 
nozzle 6 - 8 inches away from filter to prevent damage to filter. 

6.

Install air filter in case, and replace cover. 

Fuel Filter

Level 1.

Parts Required: Tune Up Kit.

A

B

Summary of Contents for SRM-410X

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands