manualshive.com logo in svg

Echo SRM-410X, Operator'S Manual

Share
Download
Echo SRM-410X Operator'S Manual Download Page 35

SRM-410X

MAINTENANCE

X7502168400

35

© 11/20 ECHO Incorporated

Operating a poorly maintained unit can result in serious injuries 
to operator or bystanders. Always follow all maintenance 
instructions as written, otherwise serious personal injury can 
result. 

Your unit is designed to provide many hours of trouble free service. Regular 

scheduled maintenance will help your unit achieve that goal. If you are 

unsure or are not equipped with the necessary tools, we recommend that 

you take your unit to a Servicing Dealer for maintenance. To help you 

decide whether you want to DO-IT-YOURSELF or have the Dealer do it, 

each maintenance task has been graded. If the task is not listed, see your 

Dealer for repairs.

The use of emission control components other than those specifically 
designed for this unit is a violation of federal law. 

Skill Levels

Level 1

 = Easy to do. Common tools may be required.

Level 2

 = Moderate difficulty. Some specialized tools may be required.

Level 3

 = See your dealer.

Click HERE or go to http://www.echo-usa.com/products/maintenance-kit 

or

HERE https://www.shindaiwa-usa.com/you-can.aspx

For information about maintenance kits.

Maintenance Intervals

COMPONENT/SYSTEM

MAINTENANCE 

PROCEDURE

SKILL 

LEVEL

Daily or Before Use

Air Filter

Inspect/Clean *

1

Choke Shutter
Fuel System

Inspect

 3

Cooling System

Inspect/Clean

2

Summary of Contents for SRM-410X

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands