manualshive.com logo in svg

Echo SRM-410X, Operator'S Manual, Page: 5 / 56

Share
Download
Echo SRM-410X Operator'S Manual Download Page 5

SRM-410X

SAFETY

X7502168400

5

© 11/20 ECHO Incorporated

The safety alert symbol accompanied by the word “WARNING” 
calls attention to an act or condition which CAN lead to serious 
personal injury or death if not avoided.

The safety alert symbol accompanied by the word “CAUTION” 
calls attention to an act or condition which might lead to minor 
or moderate personal injury if not avoided.

The enclosed message provides information necessary for the 
protection of the unit.

Note:  This enclosed message provides tips for use, care and 

maintenance of the unit.

CIRCLE AND SLASH SYMBOL

This symbol means the specific action shown is prohibited. 

Ignoring these prohibitions can result in serious or fatal injury.

International Symbols

Symbol

Description

Symbol

Description

Warning, See 

Operator’s Manual

Carburetor 

Adjustment - High 

Speed Mixture

Wear Eye, Ear 

and Head 

Protection

Carburetor 

Adjustment - Idle 

Speed

Wear Hand and 

Foot Protection

Carburetor 

Adjustment - Low 

Speed Mixture

Safety/Alert

STOP Switch

H

T

L

Summary of Contents for SRM-410X

























































Reviews:

No comments