background image

22

X7501185001

© 01/2019 ECHO Inc.

OPERATION

ES-252

Debris bag is flammable and could be ignited if allowed to 
contact hot muffler cover or exhaust.  Keep bag away from 
hot surfaces at all times. 

1. Adjust debris bag strap to support bag on operator’s 

shoulder. Bag must not be folded at intake area, or intake 
will clog. Further adjustment may be necessary as the 
debris bag fills and becomes heavier.

2. Grip throttle control handle with left hand, and lower 

handle/stand with right hand.

3. Operate unit with beveled end of tube facing downward. 

Keep tube opening close to material being vacuumed for 
best results.

4. Empty bag when debris level reaches intake opening. To empty bag, move stop switch to “STOP” 

position, and wait for blower to stop running. Loosen Velcro strap at elbow and slide bag off elbow. Open 
other end of bag, and empty contents. Close bag, and reattach to blower. Secure bag with Velcro strap.

Note:  Vacuum action works best at higher engine speeds. Avoid using vacuum in areas where rocks or 

other large, hard debris may be vacuumed into unit. Clear these areas with blower first, blowing light 
debris into a pile. Use attachment to vacuum pile.

SHRED ‘ N’ VAC

®

  Troubleshooting 

Problem

Cause

Remedy

Unit runs, but doesn’t vacuum or 
has poor suction 

Elbow or debris bag clogged  Check elbow and debris bag, and 

clear as needed.  Make sure bag 
is not folded over at intake during 
use.

Obstructions in vacuum tube  Check vacuum tube, and remove 

obstructions. Avoid wet leaves.

Unit stopped suddenly during 
vacuuming, and now starter won’t 
work 

Object stuck in fan housing 
area 

Remove vacuum tube and check 
fan area.  Remove object.

Unit jams repeatedly during use 

Material being vacuumed too 
big or too hard for blades to 
shred 

Use vacuum for leaves and small 
twigs, maximum 1/4” diameter x 
3” long

Vacuum tube difficult to install or 
remove from unit 

Tube/housing fit tight. 

Apply small amount of soapy 
water to end of tube to ease 
assembly or removal.  Turns tube 
1/4 turn to loosen for removal.

Summary of Contents for SHRED 'N' VAC ES-252

































Reviews: