background image

PB-2620

MAINTENANCE

X7501190602

27

© 10/2017 ECHO Inc.

4.

Control engine speed with 
throttle trigger (A), or for 
continuous use, set engine 
speed with throttle position 
lever (B). Rotate throttle 
position lever forward for lower 
speed, back for higher speed.

5.

Use lower speed to blow debris 
from hard surfaces.

6.

Additional speed may be 
necessary to clean debris, 
snow, etc. from lawns and 
flowerbeds.

Note:  Never use a higher speed 

setting than necessary to perform a task. Remember, the 
higher the engine speed, the louder the blower noise. 
Minimize dust by using blower at lower speeds. Keep debris 
on your property. Be Smart - be a good neighbor.

MAINTENANCE

Moving parts can amputate fingers or cause severe injuries. 
Keep hands, clothing and loose objects away from all openings. 
Always stop engine, disconnect spark plug, and make sure all 
moving parts have come to a complete stop before removing 
obstructions, clearing debris, or servicing unit. Allow unit to 
cool before performing service. Wear gloves to protect hands 
from sharp edges and hot surfaces.

Operating a poorly maintained unit can result in serious injuries 
to operator or bystanders. Always follow all maintenance 
instructions as written, otherwise serious personal injury may 
result. 

A

B

Summary of Contents for PB-2620





















































Reviews: