Echo Bear Cat SC3306 Owner'S Manual Download Page 26

Page: 26 / 32

3 INCH CHIPPER/SHREDDER

Section

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSES

REMEDY

Engine will not start

Lack of fuel or oil

Fill fuel tank and check oil level

Spark plug disconnected

Connect spark plug

Kill switch on access cover is damaged

Test kill switch. Replace if it is not working

Dirty, stale, or contaminated fuel

Drain and refill fuel tank with fresh, clean

unleaded regular gasoline or diesel.

Replace fuel filter.

Internal engine problems

See your engine dealer

Engine or rotor stalls or

stops

Chipper rotor housing or discharge tube is

plugged

Shut off engine and disengage belt

engagement. Refer to manual for

information on clearing a plugged rotor.

Never use the belt engagement to clear a

plugged rotor.

Feeding material that is too large

Limit branch size to rated capacity

Engine overheats

Cooling system plugged

Clean cooling fan and cooling fins on the

radiator or engine block

Improper coolant level

Fill engine to correct coolant level. Refer to

the engine owner’s manual

Engine stalls or

belt squeals when

engaging belt

Engaging belt too fast

Reduce engagement speed

Belt tension too loose

Adjust tensioner. Replace belt if needed.

Engine runs, but dies

or does not accelerate

properly

Air filter dirty

Clean or replace

Fuel filter dirty

Replace

Fuel vent plugged

Clean or replace

Spark plug dirty/worn

Clean and adjust or replace

Carburetor vibration

Adjust

Cooling system dirty/plugged

Clean

Spark arrestor* plugged

Clean or replace

Machine chips poorly

Dull chipper blades

Flip, sharpen, or replace

Drive belts loose or worn

Inspect drive belts, adjust or replace if

needed

Feeding material that is too large

Limit branch size to rated capacity

Before performing any of the corrections in this troubleshooting chart, refer to the appropriate information contained in

this manual for the correct safety precautions and operating or maintenance procedures. Contact your dealer or ECHO

Bear Cat

for service problems with the machine.

*If equipped

Summary of Contents for Bear Cat SC3306

































Search results

Summary of Contents for Bear Cat SC3306

Reviews:

Related manuals for Bear Cat SC3306

Brands by name

Popular brands

Echo Bear Cat SC3306, Owner'S Manual

Search results

Summary of Contents for Bear Cat SC3306

Reviews:

Related manuals for Bear Cat SC3306

Brands by name

Popular brands