![background image](http://html1.mh-extra.com/html/ecg/edf-4516-qa/edf-4516-qa_instruction-manual_3906472052.webp)
GB
52
INSTALLATION INSTRUCTIONS
WARNING!
•
Entrust the dishwasher connections for power supply and water supply to qualifi ed professionals.
•
The appliance must not stand on the supply or drain hose or on the electrical power cable.
•
The dishwasher must be connected to a water supply with a new set of hoses. Do not use an old supply
hose.
PLACEMENT OF THE DISHWASHER
•
Before installation, unpack the dishwasher and dispose of all packaging according to label instructions,
and make sure that there is no damage caused by transportation. If you fi nd any damage, stop the
installation immediately and contact your vendor.
•
When choosing a place for the dishwasher, make sure that you can load and unload dishes easily.
•
Place the dishwasher close to water supply and drain.
•
To facilitate the installation, the supply and drain hoses may be connected from left and right sides.
•
When moving the dishwasher, do not lift it holding the door or the front panel.
•
The dishwasher can also be inserted under your kitchen counter. Be careful when inserting the dishwasher
in place that you do not squeeze the supply and drain hoses. Make sure that the dishwasher is not standing
on the power cable.
•
Place the dishwasher on a fl at hard fl oor. Using the front adjustable feet, level the dishwasher horizontally.
The tilt of the dishwasher should no exceed 2°. The level horizontal position ensures greater stability,
prevents movement of the appliance and limits vibration and noise. Correct positioning of the dishwasher
will also make the opening and closing of the door easier.
•
If the dishwasher door does not close correctly, make sure the dishwasher is stable and level and if
necessary adjust the level using the adjustable levelling feet.
Note:
Maximum height of adjustable feet is 20 mm.
CONNECTING THE WATER SUPPLY HOSE
1. The water pressure must be in the range of 0,04 to 1,0 MPa. If the
water pressure is lower, contact a technician.
2. Make sure that the supply hose is not bent or twisted.
3. If the water pipes are new or have not been used for a long time,
have at fi rst fl ow out enough water until completely clean water
comes out.
4. Attach the hose to the water supply with 3/4 inch thread and
tighten fi ttings.
5. Check the tightness of the connection.
6. Open the water supply tap fully before using the dishwasher.
CONNECTING THE DRAIN HOSE
Connect the drain hose to the drain pipe and make sure that the
hose does not bend or twist. If the drain hose is too short, contact
an authorized service center to request a longer hose of the same
material. Keep in mind that the hose must not be even with an
extension longer than 4 meters. A longer drain hose would prevent
proper functioning of the dishwasher. Attach the hose fi rmly to
the drain pipe so that it will not loosen during the operation of the
dishwasher.
Connecting to the sink siphon
Drain connection must be positioned at a height between 50 cm
(minimum) and 100 cm (maximum) above the bottom of the
max1
100mm
min500mm
min120mm
min 40mm
Summary of Contents for EDF 4516 QA+
