P/N 920-0558-00 (Rev A) 2016-12-21
© 2016 at ECCO
Page 1 of 4
ECCO Safety Group Europe
Victoria Industrial Park, Victoria Road
Seacroft, Leeds, England
LS14 2LA
+44 (0)113 2375340
www.eccosafetygroup.com
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure the
safety of you and those you are seeking to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing, which
can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output performance of the
system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system without losing eye
contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment
area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death. Refer to the vehicle
owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable mounting location ensuring
the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people,
vehicles or other obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal. Never take the right-of-
way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, driving against traffic, responding at
a high rate of speed, or walking on or around traffic lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding
warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer assumes
no liability for any loss resulting from the use of this warning device.
Do not install and/or operate this safety product unless you have read and understand the safety information
contained
Failure to install or use this product according to manufacturers recommendations may result in property damage, serious injury, and/or
death to those you are seeking to protect!
!
WARNING!
Important!
This unit is a safety device, and it must be
connected to its own separate, fused power point to assure its
continued operation should any other electrical accessory fail.
5545/5550 Series - Reflex™ LED Microbars provide
a compact yet powerful warning solution that offers
the flexibility of either permanent or magnet
mounting. All models feature 12-24 VDC operation
and use LED technology to maximize light output,
offering multiple flash patterns including double, quad
quint, rotate and random.
Current Draw:
5545: 1.48 Amps Maximum
Maximum power consumption: 18.9 watts
5550: 3.8 Amps Maximum
Maximum power consumption: 48.6 watts
Flash Rate:
See Flash Pattern Chart
Temp. Range:
-30ºC to +50ºC
Installation & Mounting:
Magnet Mount:
The Magnet Mount feature includes a suction cup on the bottom of the microbar,
with a magnet inside of the suction cup, for a secure, temporary mount. The
microbar should be placed in the center of the roof where the least amount of
curvature occurs. Before installing, make sure the mounting surface is clean and
there is no debris on the bottom of the microbar or on the roof of the vehicle, which
could reduce the holding power of the suction cup and magnet. Place and remove
the microbar without sliding to avoid scratching the paint on the vehicle. After
placement, the microbar should adhere firmly to the surface. If the unit slides or
moves easily, a proper installation has not been obtained. To release, lift the tab to
release the airlock (see Figure 1). To protect the Magnet Mount assembly, return
microbar to the box when not in use.
Do not attempt to attach the microbar to an
ice-covered surface.
Carefully remove the Microbar and place it on a flat surface.
Examine the unit for transit damage, and locate all parts. If damage
is found, or parts are missing, contact the transit company or ECCO.
Do not use damaged or broken parts.
Specifications:
Size: 5545-VA1, 5545-VA1 10” x 7” x 2”
5550-VA1, 5550-VA1
5545-MAG, 5545-MAG 10” x 7” x 3”
5550-MAG, 5550-MAG
Weight:
Input Voltage: 12 to 24 VDC systems
Mount
5545
5550
Permanent Mount
approx. 0.81kg
approx. 0.91kg
Magnet Mount
approx. 1.36kg
approx. 1.95kg
Installation and Operation Instructions
5500 Series LED Microbars