background image

Chengdu Ebyte Electronic Technology Co., Ltd.

E29-400TXXX product data sheet

Copyright ©2012–2023

Chengdu Ebyte Electronic Technology Co.,Ltd.

29

Chapter 15 Antenna recommendation

15.1 Antenna recommendation

The antenna is an important role in the communication process. A good antenna can largely improve the

communication system. Therefore, we recommend some antennas for wireless modules with excellent performance
and reasonable price.

Model No.

Type

Frequency

Hz

nterface

Gain

dBi

Height

Cable

length

cm

Function & Feature

TX433-NP-4310

FPC

antenna

433M

焊接

2.0

43.8*9.5

-

Embedded FPC antenna

TX433-JZ-5

Rubber

antenna

433M

SMA-J

2.0

52

-

Short straight
&omnidirectional

TX433-JZG-6

Rubber

antenna

433M

SMA-J

2.5

62

-

Short straight
&omnidirectional

TX433-JW-5

Rubber

antenna

433M

SMA-J

2.0

50

-

Flexible &omnidirectional

TX433-JWG-7

Rubber

antenna

433M

SMA-J

2.5

75

-

Flexible &omnidirectional

TX433-JK-11

Rubber

antenna

433M

SMA-J

2.5

110

-

Flexible &omnidirectional

TX433-JK-20

Rubber

antenna

433M

SMA-J

3.0

210

-

Flexible &omnidirectional

TX433-XPL-100

Sucker

antenna

433M

SMA-J

3.5

185

100

Small sucker antenna,
cost-effictive

TX433-XP-200

Sucker

antenna

433M

SMA-J

4.0

190

200

Medium sucker
antenna,low power
comsumption

TX433-XPH-300

Sucker

antenna

433M

SMA-J

6.0

965

300

Large sucker antenna, high
gain

TX490-JZ-5

Sucker

antenna

470/490M

SMA-J

2.0

50

-

Short straight
&omnidirectional

TX490-XPL-100

Sucker

antenna

470/490M

SMA-J

3.5

120

100

Small sucker antenna,
cost-effictive

Summary of Contents for E29-T Series
































Reviews: