manualshive.com logo in svg

EBS CPX200NB, Installation And Programming Manual

Share
Download
EBS CPX200NB Installation And Programming Manual Download Page 93

 

CPX200NB ALARM CONTROL UNIT – INSTALLER MANUAL  

 

  93 / 116 

- Keypad communication lost 
- Keypad tamper 
- Keypad power failure 
- Time lost 

 

10.2.

 

THE BEHAVIOR OF THE SYSTEM IN COMPATIBILITY MODE FOR 

GRADE 2 

The system operates in accordance with the EN 50131 standard requirements for Grade 2, 

i.e.: 

 

zones status is available only after user code has been entered 

 

information about alarms is available only after user code has been entered 

 

information about alarms memory is available only after user code has been entered 

 

information about failures is available only after user code has been entered 

 

information about failures memory is available only after user code has been entered 

 

arming requires authorization 

 

prior to arming, the control panel checks circumstances that may prevent arming 

 

the codes in the system must be at least 5 characters 

 

after entering an invalid code three times, all keypads in the system will be blocked 

for 90 seconds. 

 

Summary of Contents for CPX200NB





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands