EAVISION E-A2020 User Manual Download Page 14

Page: 14 / 67

5. Check List before Use

5.1 Materials

⚫

Integrated Remote Control

⚫

E-A2020 Series Full-scope Perception Intelligent Plant Protection UAV

⚫

EAVISION Agriculture APP

⚫

Battery

⚫

Charger

（

remote control charger

，

main battery charger

）

5.2 Remote Control

⚫

Check whether the remote control antenna is damaged and whether the screws

are loose.

⚫

Open the remote control and check the battery power. Please charge the remote

control in time if the battery power is lower than 50%.

⚫

The remote control can connect to the UAV.

5.3 UAV

⚫

Check the screws of the UAV arms, motor and propellers. Please tighten the

screws if they are loose.

⚫

Check the status of the UAV holder. Please replace it in time if there is

deformation.

⚫

Check whether there is blockage inside the spray nozzle. Please clean it in time if

there is blockage.

Summary of Contents for E-A2020




































































Search results

Summary of Contents for E-A2020

Reviews:

Brands by name

Popular brands

EAVISION E-A2020, User Manual

Search results

Summary of Contents for E-A2020

Reviews:

Brands by name

Popular brands