background image

RE SERIES_ RevA

  

3/5/2022 

 

 

15 

Leveling

 

WARNING: Level the enclosure before attempting to install equipment. The casters are not designed to provide long-term support for the 
enclosure. Use the levelers to provide long-term support. Install the enclosure in a structurally sound area with a level floor that is able to 
bear the weight of the enclosure, all equipment that will be installed in the enclosure and any other enclosures and/or equipment that will be 
installed nearby.

 

 1 

After the enclosure has been moved to the installation location, use a carpenter's level to check 

the slope of the floor. If the floor slopes more than 1%, choose an alternate installation site.

 

 
 

 
 
 

 

 

 2 

Use an 18 mm open-end wrench to lower each leveler

 

until it reaches the floor. (There are 4 

levelers, 2 at the front and 2 at the rear.) Make sure each leveler contacts the floor solidly.

 

Note: 

Lower a leveler by turning it clockwise; raise a leveler by turning it counter-clockwise.

 

 
 
 
 
 

 

 3 

After lowering each leveler, use the carpenter's level to confirm that the enclosure is level in all 

directions. Adjust the levelers as required until the enclosure is level.

 

 
 
 

 
 

 

 

 4 

In order to secure the cabinet to the building structure for stability, attach the 2 shipping brackets 

using the hardware that attached the enclosure to the shipping pallet. Use a 13 mm open-end 
wrench to connect the brackets to the outer

 

or inner

 

bracket mounting points of the 

enclosure. Attach the brackets to secure mounting points in the floor using user-supplied 
hardware.

 

 
 

 
 
 

Ground Connection

 

All the parts of the enclosure are grounded to the frame of the enclosure. Use the enclosure's front or 
rear threaded grounding point

 

and an M6 screw (included) to connect the frame of the enclosure 

directly to your facility's earth ground connection with an 8 AWG ( D=3.2 mm ) wire(user-supplied). 
Route the ground wire under the enclosure's frame to ensure unhindered door operation. 

WARNING: Attach each enclosure to earth ground separately. Do not use the enclosure 
without an earth ground connection.

 

 
 
 
 
 
 
 
 
 

 

 3

 

FLOOR

 

 1

 

 

 

 

 2

 

 B

 

 A

 

 4

 

Summary of Contents for RE Series
























Reviews: