Eaton PH Series Installation Instructions Manual Download Page 8

Instruction Manual 

IM01005022E

Effective April 2014

Installation Instructions for Eaton Surge Protective

Device xxPHxxxxx and xxPVxxxxx 

Eaton

Electrical Sector

1000 Eaton Boulevard

Cleveland, OH 44122

United States

877-ETN-CARE (877-386-2273)

Eaton.com

© 2014 Eaton

All Rights Reserved

Printed in USA

Publication No. IM01005022E / TBG001101

April 2014

Eaton is a registered trademark. 

All other trademarks are property of their 

respective owners.

Warranty

Eaton warrants these products for a period of 10 years from the 

date of delivery to the purchaser, 15 years if the product is properly 

registered with Eaton, to be free from defects in both workmanship 

and materials . Eaton assumes no risk or liability for results of the 

use of the products purchased from it, including but without limiting 

the generality of the foregoing: (1) The use in combination with any 

electrical or electronic components, circuits, systems, assemblies, 

or any other materials or substances; (2) Unsuitability of any product 

for use in any circuit or assembly .
Register products on-line at www .eaton .com/spd .  After the page 

opens click on the “Warranty Registration” link in the right hand col-

umn .
Purchaser’s rights under the warranty shall consist solely of requir-

ing Eaton to repair, or at Eaton’s sole discretion, replace, free of 

charge, F .O .B . factory, and defective items received at said factory 

within said term determined by Eaton to be defective . The giving of 

or failure to give any advice or recommendations by Eaton shall not 

constitute any warranty by or impose any liability upon Eaton . The 

foregoing constitutes the sole and exclusive liability of Eaton AND 

IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED, 

IMPLIED OR STATUTORY AS TO THE MERCHANTABILITY, FITNESS 

FOR PURPOSE SOLD, DESCRIPTION, QUALITY, PRODUCTIVENESS 

OR ANY OTHER MATTER .
In no event shall Eaton be liable for special or consequential dam-

ages or for delay in performance of the warranty .
This warranty does not apply if the product has been misused, 

abused, altered, tampered with, or used in applications other than 

specified on the nameplate . At the end of the warranty period, Eaton 

shall be under no further warranty obligation expressed or implied .
The product covered by this warranty certificate can only be  

repaired or replaced by the factory . For help on troubleshooting the 

SPD, or for warranty information, call 1-800-809-2772, Option 4, 

sub-option 2 . Repair or replacement units will be returned collect . If 

Eaton finds the return to be a manufacturer’s defect, the product will 

be returned prepaid .

Summary of Contents for PH Series









Reviews: